Kia K4: Engine Control / Fuel System / Engine Control System

Contents:

Description and Operation ➤

Accelerator Position Sensor (APS) Specification

Specification
Accelerator Pedal Position
Output Voltage (V)
APS1
APS2
Accelerator pedal is not pressed (*E.C.P)
0.7 - 0.8
0.325 - 0.425
Accelerator pedal is fully pressed (*W.O.T)
3.98 - 4.22
1.975 - 2.125

*E.C.P : Electrically Close Position *W.O.T : Wide Open Throttle

Accelerator Position Sensor (APS) Description and Operation

Description
• Accelerator Position Sensor (APS) is mounted on the accelerator pedal module and is an important sensor that transmits the driver's accelerating action to Engine Control Module (ECM) to determine the amount of fuel injection according to the required acceleration speed.
• The APS is one of the most important sensors in engine control system, which consists of the two sensors working individually.
• Each sensor is composed of an independent circuit, Sensor 2 outputs 50% of signal value of Sensor 1 and the APS is determined to be a fault when the proportion of voltage for each sensor is out of certain range.

Engine Control / Fuel System — Engine Control System / Accelerator Position Sensor (APS) / Description and Operation / Description illustration

Accelerator Position Sensor (APS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self Diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data Analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
Accelerator Pedal Position
Output Voltage (V)
APS1
APS2
Accelerator pedal is not pressed (*E.C.P)
0.7 - 0.8
0.325 - 0.425
Accelerator pedal is fully pressed (*W.O.T)
3.98 - 4.22
1.975 - 2.125

*E.C.P : Electrically Close Position *W.O.T : Wide Open Throttle
Information    
Refer to the KDS screen for operating conditions and details

Accelerator Position Sensor (APS) Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Remove the accelerator pedal module (A) after removing the nuts.
Tightening torque : 12.7 - 15.7 N·m (1.3 - 1.6 kgf·m, 9.4 - 11.6 lb·ft)

Engine Control / Fuel System — Engine Control System / Accelerator Position Sensor (APS) / Removal and Installation / Removal illustration

3. Disconnect the connector (B) from the accelerator pedal module (A).

Engine Control / Fuel System — Engine Control System / Accelerator Position Sensor (APS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the accelerator pedal module to the specified torque.
• If the accelerator pedal module is dropped, it may cause internal damage. (Do not reuse)

Boost Pressure Sensor (BPS) Specification

Specification
Item
Specification
Rated voltage (V)
5
Operating voltage (V)
4.75 - 5.25
Output voltage (V)
0.5 - 4.5

[Pressure Signal]
Pressure
Output Voltage (V)
kPa
kg/cm²
psi
10
0.1
1.45
0.5
40
0.4
5.80
0.913
80
0.8
11.60
1.465
120
1.2
17.40
2.017
160
1.6
23.20
2.569
200
2.0
29.00
3.120
220
2.2
31.90
3.396
240
2.4
34.80
3.672
280
2.8
40.61
4.224
300
3.0
43.51
4.5

Boost Pressure Sensor (BPS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Boost Pressure Sensor (BPS) / Components and Components Location / Component Location illustration

1. Boost Pressure Sensor (BPS)
1-a. 8.8 - 10.8 N·m (0.9 - 1.1 kgf·m, 6.5 - 8.0 lb·ft)

Boost Pressure Sensor (BPS) Description and Operation

Description
Boost Pressure Sensor (BPS) is mounted on Electronic Throttle Control (ETC) module and measures the pressure of the supercharged intake air from the turbocharger.

Engine Control / Fuel System — Engine Control System / Boost Pressure Sensor (BPS) / Description and Operation / Description illustration

Boost Pressure Sensor (BPS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self Diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data Analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
Pressure
Output Voltage (V)
kPa
kg/cm²
psi
10
0.1
1.45
0.5
40
0.4
5.80
0.913
80
0.8
11.60
1.465
120
1.2
17.40
2.017
160
1.6
23.20
2.569
200
2.0
29.00
3.120
220
2.2
31.90
3.396
240
2.4
34.80
3.672
280
2.8
40.61
4.224
300
3.0
43.51
4.5

Information    
Refer to the KDS screen for operating conditions and details

Boost Pressure Sensor (BPS) Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Disconnect the Boost Pressure Sensor (BPS) connector (A).

Engine Control / Fuel System — Engine Control System / Boost Pressure Sensor (BPS) / Removal and Installation / Removal illustration

3. Remove the BPS (A) after removing the bolt.
Tightening torque : 8.8 - 10.8 N·m (0.9 - 1.1 kgf·m, 6.5 - 8.0 lb·ft)

Engine Control / Fuel System — Engine Control System / Boost Pressure Sensor (BPS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Boost Pressure Sensor (BPS) to the specified torque.
• If the BPS is dropped, it may cause internal damage. (Do not reuse)

Camshaft Position Sensor (CMPS) Specification

Specification
Item
Specification
Operating current (mA)
Maximum 10
Operating voltage (V)
4.75 - 5.25
Output voltage (V)
0.6 - 4.5

Camshaft Position Sensor (CMPS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Components and Components Location / Component Location illustration

1. Camshaft Position Sensor (CMPS) - Intake
1-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
2. High Pressure Fuel Pump Foam
3. CMPS - Exhaust
3-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Camshaft Position Sensor (CMPS) Description and Operation

Description
• The Camshaft Position Sensor (CMPS) is a hall sensor, which detects the camshaft position by using a hall element.
• It is synchronized with Crankshaft Position Sensor (CKPS) and detects the piston position of each cylinder which cannot be detected by the CKPS.
• The two CMPS are installed on engine head cover of bank 1 and 2 (intake, exhaust) respectively and use a target wheel installed on the camshaft.
• Engine Control Module (ECM) detects the cycle of each cylinder based on the CMPS signal and controls the fuel injection of each cylinder.

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Description and Operation / Description illustration

Camshaft Position Sensor (CMPS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Actuation test : Checking the Camshaft Position Sensor (CMPS) operation condition (Data Analysis → System Selection → Engine → Actuation test → Oil Control Valve - Intake Bank1 / Oil Control Valve - Exhaust Bank1 (Option))
Information    
Refer to the KDS screen for operating conditions and details
Component Inspection
1. Check signal waveform of Camshaft Position Sensor (CMPS) with the KDS.
Specified value : Refer to "DTC diagnostic guide"

Camshaft Position Sensor (CMPS) Removal and Installation

Removal
Caution    
Wait for the engine to cool down to avoid burns from the high temperatures of the exhaust system.
Intake
1. Disconnect the Camshaft Position Sensor (CMPS) connector (A).

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration

2. Remove the CMPS (A) after removing the bolt.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration

Exhaust
1. Disconnect the battery negative ( - ) terminal.
2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
3. Separate the breather hose (A) after releasing the clamp.

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration

4. Remove the high pressure fuel pump foam (A).

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration

5. Disconnect the Camshaft Position Sensor (CMPS) connector (A).

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration

6. Remove the CMPS (A) after removing the bolt.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Camshaft Position Sensor (CMPS) to the specified torque.
• If the CMPS is dropped, it may cause internal damage. (Do not reuse)
• Apply the engine oil to the O-ring (A).

Engine Control / Fuel System — Engine Control System / Camshaft Position Sensor (CMPS) / Removal and Installation / Installation illustration

• Install the CMPS by pushing it into the installation hole firmly. and be careful not to damage the sensor.

Crankshaft Position Sensor (CKPS) Specification

Specification
Item
Specification
Operating voltage (V)
4.5 - 5.5
Current consumption (mA)
Maximum 12

Crankshaft Position Sensor (CKPS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Components and Components Location / Component Location illustration

1. Crankshaft Position Sensor (CKPS) Bracket
1-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
2. CKPS
2-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Crankshaft Position Sensor (CKPS) Description and Operation

Description
• The Crankshaft Position Sensor (CKPS) is a sensor that detects the engine rotation speed (rpm).
• The engine rotation speed (rpm) is the most important variable in the electronic control engine, and if the engine rotation speed signal is not input to the Engine Control Module (ECM), the engine may stop due to the CKPS signal not being input.
• The CKPS determines which stroke the current piston position is on by the target-wheel, and the target-wheel consists of 58 slots and 2 empty slots at 360 degrees of Crank Angle (CA).

Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Description and Operation / Description illustration

Crankshaft Position Sensor (CKPS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
Information    
Refer to the KDS screen for operating conditions and details
Component Inspection
1. Check signal waveform of Crankshaft Position Sensor (CKPS) with the KDS.
Specified value : Refer to "DTC diagnostic guide"

Crankshaft Position Sensor (CKPS) Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Remove the engine room under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")
3. Disconnect the Crankshaft Position Sensor (CKPS) connector (A).

Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Removal and Installation / Removal illustration

4. Separate the CKPS connector (A) by using hook/pick tool from the bracket.

Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Removal and Installation / Removal illustration

5. Remove the CKPS (A) after removing the bolt and fastener (B).
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Crankshaft Position Sensor (CKPS) to the specified torque.
• If the CKPS is dropped, it may cause internal damage. (Do not reuse)
• Apply the engine oil to the O-ring (A).

Engine Control / Fuel System — Engine Control System / Crankshaft Position Sensor (CKPS) / Removal and Installation / Installation illustration

CVVD Actuator Specification

Specification
Item
Specification
Operating voltage (V)
9.1 - 16.0
Rated voltage (V)
18
Insulated resistance (MΩ)
Minimum 10

CVVD Actuator Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / CVVD Actuator / Components and Components Location / Component Location illustration

1. High Pressure Fuel Pump Foam
2. High Pressure Fuel Pipe
2-a. 32.4 - 35.3 N·m (3.3 - 3.6 kgf·m, 23.9 - 26.0 lb·ft)
2-b. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
3. Continuous Variable Valve Duration (CVVD) Actuator
3-a. 18.6 - 24.5 N·m (1.9 - 2.5 kgf·m, 13.7 - 18.1 lb·ft)

CVVD Actuator Description and Operation

Description
The Continuous Variable Valve Duration (CVVD) actuator controls the optimum opening / closing time by changing the valve opening section according to the driving conditions.

Engine Control / Fuel System — Engine Control System / CVVD Actuator / Description and Operation / Description illustration

CVVD Actuator On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
(3) Actuation test : Checking the system operation condition (Data Analysis → System Selection → Engine → Actuation Test → CVVD Intake)
Information    
Refer to the KDS screen for operating conditions and details

CVVD Actuator Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Remove the high pressure fuel pipe. (Refer to Fuel Delivery System - "Fuel Line")
3. Disconnect the Continuous Variable Valve Duration (CVVD) actuator connector (A).

Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Removal illustration

4. Separate the ground wiring (A) after removing the bolt.
Tightening torque : 7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Removal illustration

5. Remove the CVVD actuator (A) after removing the bolts.
Tightening torque : 18.6 - 24.5 N·m (1.9 - 2.5 kgf·m, 13.7 - 18.1 lb·ft)

Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Continuous Variable Valve Duration (CVVD) actuator to the specified torque.
• If the CVVD actuator is dropped, it may cause internal damage. (Do not reuse)
• When installing the CVVD actuator, insert dowel pin (B) certainly into the cam carrier hole after inserting the shaft (A).

Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Installation illustration

• Tighten the bolts in the following order. Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Installation illustration Pre-tighten -> Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Installation illustration Tighten -> Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Installation illustration Tighten -> Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Installation illustration Tighten

Engine Control / Fuel System — Engine Control System / CVVD Actuator / Removal and Installation / Installation illustration

2. Perform the CVVD Intake Adaptation after replacing the CVVD actuator. (S/W Management → Engine Control → CVVD learning)
Information    
Refer to the KDS screen for operating conditions and details

Electric Waste Gate Actuator (EWGA) Specification

Specification
Item
Specification
DC Motor
Operating voltage (V)
13.5
Frequency (kHz)
1 - 5
Current (A)
Maximum 6.5 (Room temperature)
Sensor
Operating voltage (V)
4.9 - 5.1

Electric Waste Gate Actuator (EWGA) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Electric Waste Gate Actuator (EWGA) / Components and Components Location / Component Location illustration

1. Elbow Pipe
1-a. 12.7 - 13.7 N·m (1.3 - 1.4 kgf·m, 9.4 - 10.1 lb·ft)
2. Retaining Ring
3. Electric Waste Gate Actuator (EWGA)
3-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
4. Turbocharger

Electric Waste Gate Actuator (EWGA) Description and Operation

Description
• The Electric Waste Gate Actuator (EWGA) is mounted on the turbocharger.
• EWGA regulates the compressed air by controlling the turbocharger waste gate valve based on Pulse Width Modulation (PWM) signal from Engine Control Module (ECM).

Engine Control / Fuel System — Engine Control System / Electric Waste Gate Actuator (EWGA) / Description and Operation / Description illustration

Electric Waste Gate Actuator (EWGA) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
(3) Actuation test : Checking the system operation condition (Data Analysis → System Selection → Engine → Actuation Test → Turbo waste gate(WGT) Valve)
Information    
Refer to the KDS screen for operating conditions and details

Electric Waste Gate Actuator (EWGA) Removal and Installation

Removal
1. Remove the Electric Waste Gate Actuator (EWGA) from the turbo manifold. (Refer to Engine Mechanical System - "Turbo Manifold")
Installation
1. Install in the reverse order of removal.
Note    
• Install the Electric Waste Gate Actuator (EWGA) to the specified torque.
• If the EWGA is dropped, it may cause internal damage. (Do not reuse)
• After installing, check that retaining ring is certainly engaged by turning the it over 90°.

Electric Waste Gate Actuator (EWGA) Adjustment

Adjustment
[Rod Adjustment Procedure Flowchart]

Engine Control / Fuel System — Engine Control System / Electric Waste Gate Actuator (EWGA) / Adjustment illustration

Caution    
To prevent burns due to the high heat, work when the temperature of the engine and the surrounding area is sufficiently low.
1. Turn the IG OFF.
2. Connect the KDS to the self-diagnosis connector (DLC).
3. Turn the IG ON.
Note    
Do not start the engine. This is a crucial step to read the correct adaptation value.
4. Without starting the engine, cycle the ignition ON for 5 sec then ignition OFF for 5 sec then check the "Adaption value for the low mechanical stop of Electric Waste Gate Actuator (EWGA)" on the KDS.
Voltage (V) : 3.5 - 3.7
Note    
Do not start the engine to measure an accurate value.
Information    
Refer to the KDS screen for operating conditions and details
5. If the closed position voltage is not within the range of specified values, re-adjust the load length as shown below.
(1) Slightly loosen the lock nut (B) of EWGA rod (A).

Engine Control / Fuel System — Engine Control System / Electric Waste Gate Actuator (EWGA) / Adjustment illustration

(2) Remove the rod (A) after removing the retaining rings (B).

Engine Control / Fuel System — Engine Control System / Electric Waste Gate Actuator (EWGA) / Adjustment illustration

Note    
Be careful not to lose the retaining ring when removing it.
(3) Adjust the rod end to meet the specified value.

Engine Control / Fuel System — Engine Control System / Electric Waste Gate Actuator (EWGA) / Adjustment illustration

Adjustment Direction of Rod End
Voltage
Rod Length
Clockwise (A)
Rise
Shorter
Counter clockwise (B)
Drop
Longer

The Length Changes According to the Rotation Angle of The Rod
Changing Level of The Adaptation Value
180° : 0.5 mm (0.01in.)
About 0.1 V

For example) The closed position voltage of the wastegate valve has detected as 3.4 V → turn the rod end 180 degrees clockwise to increase the voltage by about 0.1 V.
6. Install the rod (A) to the turbocharger lever temporarily. Do not tighten the lock nut (B) but also not install the retaining ring.

Engine Control / Fuel System — Engine Control System / Electric Waste Gate Actuator (EWGA) / Adjustment illustration

7. Check " Adaption value for the lower mechanical stop of EWGA" after selecting "Current Data" menu. Turn the ignition ON/OFF repeatedly until the changing value of " Adaptation value for the lower mechanical stop of EWGA" is within 0.05 V.
Note    
Maintain IG ON/OFF for 5 seconds each.
8. If the voltage value measured is not within the specified voltage value, repeat 5 - 7 procedures until the voltage value is within the specified voltage value.
9. If it is within the specified voltage value, install the retaining rings (B) after tightening the lock nut (A).

Engine Control / Fuel System — Engine Control System / Electric Waste Gate Actuator (EWGA) / Adjustment illustration

Electronic Throttle Control (ETC) Module Specification

Specification
Item
Specification
Motor
Type
DC Motor
Operating voltage (V)
7.5 - 16.0
Coil resistance (Ω)
1.287 - 1.573 (Room temperature)
Sensor
Supply voltage (V)
5
Sensor Output Voltage (V)
Throttle angle (°)
TPS 1
TPS 2
0
0.5
4.5
10
0.96
4.05
20
1.41
3.59
30
1.87
3.14
40
2.32
2.68
50
2.78
2.23
60
3.23
1.77
70
3.69
1.32
80
4.14
0.86
90
4.60
0.41
91.2
4.65
0.35
*E.C.P (0°)
0.5
4.5
*W.O.T (82°)
4.23
0.77

*E.C.P : Electrically Close Position *W.O.T : Wide Open Throttle

Electronic Throttle Control (ETC) Module Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Components and Components Location / Component Location illustration

1. Boost Pressure Sensor (BPS)
1-a. 8.8 - 10.8 N·m (0.9 - 1.1 kgf·m, 6.5 - 8.0 lb·ft)
2. Intercooler Hose
3. Electronic Throttle Control (ETC) Module
3-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
4. Gasket

Electronic Throttle Control (ETC) Module Description and Operation

Description
• Electronic Throttle Control (ETC) system is a system that controls the throttle valve electronically.
• The ETC system consists of a throttle body with an integrated control motor and Throttle Position Sensor (TPS).
• The Engine Control Module (ECM) uses the Accelerator Position Sensor (APS) signal to calculate the target throttle angle the position of the throttle is then adjusted by ECM control via the ETC motor.

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Description and Operation / Description illustration

Electronic Throttle Control (ETC) Module Troubleshooting

Troubleshooting
Fail-Safe Mode
Item
Fail Safe
Electronic Throttle Control (ETC) Motor
Throttle valve stuck at 9.2°
Throttle Position Sensor (TPS)
TPS 1 fault
Using the TPS 2 signal
TPS 2 fault
Using the TPS 1 signal
TPS 1, 2 fault
Throttle valve stuck at 9.2°
Accelerator Position Sensor (APS)
APS 1 fault
Using the APS 2 signal
APS 2 fault
Using the APS 1 signal
APS 1, 2 fault
Throttle valve stuck at 9.2°

Information    
When throttle value is stuck at 9.2°, engine speed is limited at below 1,500 rpm and vehicle speed at maximum 40 - 50 km/h (25 - 31 mph)

Electronic Throttle Control (ETC) Module On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data analysis : Checking the system input/output data state (Data Analysis → System Selection → Engine)
(3) Actuation test : Checking the system operation condition (Data Analysis → System Selection → Engine → Actuation test → ETC Motor)
Information    
Refer to the KDS screen for operating conditions and details
Component Inspection
Throttle Position Sensor (TPS)
1. Disconnect the electronic throttle control (ETC) module connector (A).

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / On Vehicle Inspection illustration

2. Connect the KDS.
3. Start the engine and measure the output voltage of TPS 1 and 2 at E.C.P. and W.O.T.

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / On Vehicle Inspection illustration

Terminal
Function
4
Throttle Position Sensor (TPS) 2
5
Sensor ground
6
Throttle Position Sensor (TPS) 1

Item
Specification
Sensor Output Voltage (V)
Throttle Angle (°)
TPS 1
TPS 2
0
0.5
4.5
10
0.96
4.05
20
1.41
3.59
30
1.87
3.14
40
2.32
2.68
50
2.78
2.23
60
3.23
1.77
70
3.69
1.32
80
4.14
0.86
90
4.60
0.41
91.2
4.65
0.35
*E.C.P (0°)
0.5
4.5
**W.O.T (82°)
4.23
0.77

*E.C.P : Electrically Close Position *W.O.T : Wide Open Throttle
Electronic Throttle Control (ETC) Motor
1. Disconnect the electronic throttle control (ETC) Module connector (A).

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / On Vehicle Inspection illustration

2. Measure resistance between the ETC module terminals 1 and 2 after disconnecting the connector.
Specified value (Ω) : 1.287 - 1.573 (Room temperature)

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / On Vehicle Inspection illustration

Terminal
Function
1
Motor ( + )
2
Motor ( - )

Electronic Throttle Control (ETC) Module Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Remove the Boost Pressure Sensor (BPS). (Refer to Engine Control System - "Boost Pressure Sensor (BPS)")
3. Separate the air intake hose (A).

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration

Information    
1) Pull the quick-connector clamp (A) in the direction of the arrow when separating the air intake hose.

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration

2) After moving the quick connector clamp (B) to (C) position as shown in the figure below, pull out the air intake hose to separate it.

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration

4. Disconnect the Electronic Throttle Control (ETC) module connector (A).

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration

5. Remove the ETC module (A) by removing the bolts.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Electronic Throttle Control (ETC) module to the specified torque.
• If the ETC module is dropped, it may cause internal damage. (Do not reuse)
• Replace with a new gasket (A) and check to verify that the gasket seats properly before Installation.

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Removal and Installation / Installation illustration

2. Reset the Engine Control Module (ECM) adaptive values after replacing the ETC. (S/W Management → Engine Control → Resetting Adaptive Values)
Information    
Refer to the KDS screen for operating conditions and details
3. Perform the Electronic Throttle Control (ETC) module learning procedure. (Refer to Electronic Throttle Control (ETC) Module - "Adjustment")

Electronic Throttle Control (ETC) Module Adjustment

Adjustment
Note    
• Must perform the Electronic Throttle Control (ETC) learning procedure after replacing or reinstalling the ETC.
• If not performing the ETC learning procedure after replacing or re-installing, MIL or DTCs might occur.
1. Wait for 1 minute with the IG ON.
2. Start the engine and keep the idle status for 15 minutes.
3. Waif for 1 minute with the IG OFF.
4. Restart the engine, check that the idle speed is stable.

Electronic Throttle Control (ETC) Module Cleaning

Cleaning
1. Remove the Electronic Throttle Control (ETC) module. (Refer to Electronic Throttle Control (ETC) Module - "Removal and Installation")
Note    
Cleaning the ETC after removing it.
2. Using a cleaner and soft cloth to clean the contaminated area inside the throttle body.

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Cleaning illustration

Engine Control / Fuel System — Engine Control System / Electronic Throttle Control (ETC) Module / Cleaning illustration

Note    
• Be careful not to get foreign matter into the ETC.
• Do not spray cleaning fluid to ETC directly and use a lint free cloth moistened with throttle cleaning fluid.
• Be careful as fingers or cloth may get caught in the valve.
• Be careful not to wipe the coating liquid (displayed area) around the shaft. If the coating liquid is removed, a poor idle control may occur due to the inflow of foreign matters into the shaft inner bearing and an excessive amount of air leaking.
3. Install in the reverse order of removal.

Engine Control Module (ECM) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Components and Components Location / Component Location illustration

1. Engine Control Module (ECM)
1-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)


Engine Control Module (ECM) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) S/W Management : Controlling other features including system option setting and zero point adjustment (S/W Management → Engine Control → Resetting Adaptive Values)
Information    
Refer to the KDS screen for operating conditions and details

Engine Control Module (ECM) Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Disconnect the Engine Control Module (ECM) connectors (A).

Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Removal and Installation / Removal illustration

3. Remove the ECM (A) after removing the bolts.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Removal and Installation / Removal illustration

4. Remove the ECM (A) from the bracket after removing the bolts.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Engine Control Module (ECM) to the specified torque.
• If the ECM is dropped, it may cause internal damage. (Do not reuse)
2. ECM should be performed the reset and learning procedure after replacing it with a new one. (Refer to Engine Control Module (ECM) - "Adjustment")

Engine Control Module (ECM) Inspection

Inspection
1. TEST Engine Control Module (ECM) ground circuit : Measure resistance between ECM and chassis ground using the backside of ECM harness connector as ECM side check point. If the problem is found, repair it.
Specification (Ω) : Below 1
2. Test ECM connector : Disconnect the ECM connector and visually check the ground terminals on ECM side and harness side for bent pins or poor contact pressure. If the problem is found, repair it.
3. If problem is not found in Step 1 and 2, the ECM could be faulty. If so, replace the ECM with a new one, and then check the vehicle again. If the vehicle operates normally then the problem was likely with the ECM.
4. Re-test the original ECM : Install the original ECM (may be broken) into a known-good vehicle and check the vehicle. If the problem occurs again, replace the original ECM with a new one. If problem does not occur, this is intermittent problem.

Engine Control Module (ECM) Adjustment

Adjustment
Information    
Perform in the order below with the KDS.

Engine Control / Fuel System — Engine Control System / Engine Control Module (ECM) / Adjustment illustration

1. Perform the procedures below with the KDS when replacing the Engine Control Module (ECM) with a reused one.
(1) Perform the resetting adaptive values. (S/W Management → Engine Control → Resetting Adaptive Values)
(2) Perform the immobilizer neutral mode / smart key neutralization mode.
• Non-Smart Key type (S/W Management → Immobilizer → Neutral Mode)
• Smart Key type (S/W Management → Smart Key Unit → Neutralization Mode)
(3) Perform the auto detected configuration reset. (S/W Management → Engine Control → Auto Detected Configuration Reset)
2. Perform the "Key Teaching" procedure with the KDS.
• Non-Smart Key type (S/W Management → Immobilizer → LEARNT KEYS)
• Smart Key type Turn IG ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically.
3. Perform the VIN writing procedure with the KDS. (S/W Management → Engine Control → Write VIN)
Information    
Refer to the KDS screen for operating conditions and details
1. Perform the Electronic Throttle Control (ETC) module learning procedure. (Refer to Engine Control/Fuel System - "Electronic Throttle Control (ETC) Module")

Engine Coolant Temperature Sensor (ECTS) Specification

Specification
Item
Specification
Operating voltage (V)
4.75 - 5.25

Temperature
Resistance (kΩ)
°C
°F
-40
-40
41.74 - 54.54
-30
-22
23.54 - 29.94
-20
-4
14.13 - 16.83
-10
14
8.39 - 10.22
0
32
5.28 - 6.29
10
50
3.42 - 4.00
20
68
2.31 - 2.59
30
86
1.55 - 1.76
40
104
1.08 - 1.21
50
122
0.77 - 0.85
60
140
0.56 - 0.61
70
158
0.41 - 0.44
80
176
0.31 - 0.33
90
194
0.23 - 0.25
100
212
0.18 - 0.19
110
230
0.145 - 0.149
120
248
0.113 - 0.118
130
266
0.090 - 0.095
140
284
0.073 - 0.077
150
302
0.059 - 0.063

Engine Coolant Temperature Sensor (ECTS) Components and Components Location

Component
Engine Coolant Temperature Sensor (ECTS) #1

Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Components and Components Location / Component illustration

1. Engine Cover
2. Air Duct
3. Air Cleaner Assembly
3-a. 7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
3-b. 2.9 - 4.9 N·m (0.3 - 0.5 kgf·m, 2.2 - 3.6 lb·ft, 26.0 - 43.4 lb·in)
4. High Pressure Fuel Pump Foam
5. Intake Manifold
5-a. 18.6 - 23.5 N·m (1.9 - 2.4 kgf·m, 13.7 - 17.4 lb·ft)
6. Injector Foam
7. High Pressure Fuel Pipe
7-a. 32.4 - 35.3 N·m (3.3 - 3.6 kgf·m, 23.9 - 26.0 lb·ft)
7-b. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
8. Injector & Delivery Pipe Wiring
9. Injector & Delivery Pipe Assembly
9-a. 24.5 - 27.5 N·m (2.5 - 2.8 kgf·m, 18.1 - 20.3 lb·ft)
10. Engine Coolant Temperature Sensor (ECTS) #1
10-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Coolant Temperature Sensor (ECTS) #2

Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Components and Components Location / Component illustration

1. Drive Belt
2. Drive Belt Tensioner
2-a. 34.3 - 41.2 N·m (3.5 - 4.2 kgf·m, 25.3 - 30.4 lb·ft)
2-b. 18.6 - 23.5 N·m (1.9 - 2.4 kgf·m, 13.7 - 17.4 lb·ft)
3. Alternator
3-a. 18.6 - 24.5 N·m (1.9 - 2.5 kgf·m, 13.7 - 18.1 lb·ft)
3-b. 29.4 - 41.2 N·m (3.0 - 4.2 kgf·m, 21.7 - 30.4 Ib·ft)
4. Engine Coolant Temperature Sensor (ECTS) #2
4-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Coolant Temperature Sensor (ECTS) Description and Operation

Description
• Engine Coolant Temperature Sensor (ECTS) detects the engine coolant temperature.
• The thermistor of ECTS has a characteristic of Negative Temperature Coefficient (NTC), which means temperature and resistance are inversely proportional to each other.
• The reference +5 V is supplied to the ECTS via a resistor in the Engine Control Module (ECM). That is, the resistor in the ECM and the thermistor in the ECTS are connected in series.
• To prevent the engine stop or hesitation during the cold start, the ECM calibrates the fuel injection amount and the injection timing based on the engine coolant temperature information.

Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Description and Operation / Description illustration

Engine Coolant Temperature Sensor (ECTS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
Information    
Refer to the KDS screen for operating conditions and details
Component Inspection
1. Check the coolant temperature with the KDS.
2. Measure the resistance after disconnecting the ECTS connector.
Temperature
Resistance (kΩ)
°C
°F
-40
-40
41.74 - 54.54
-30
-22
23.54 - 29.94
-20
-4
14.13 - 16.83
-10
14
8.39 - 10.22
0
32
5.28 - 6.29
10
50
3.42 - 4.00
20
68
2.31 - 2.59
30
86
1.55 - 1.76
40
104
1.08 - 1.21
50
122
0.77 - 0.85
60
140
0.56 - 0.61
70
158
0.41 - 0.44
80
176
0.31 - 0.33
90
194
0.23 - 0.25
100
212
0.18 - 0.19
110
230
0.145 - 0.149
120
248
0.113 - 0.118
130
266
0.090 - 0.095
140
284
0.073 - 0.077
150
302
0.059 - 0.063

Engine Coolant Temperature Sensor (ECTS) Removal and Installation

Removal
Engine Coolant Temperature Sensor (ECTS) #1 - Cylinder Head
Caution    
Since there is a risk of injury due to high pressure fuel leakage, do not perform any work right after the engine is stopped.
1. Drain the coolant. (Refer to Engine Mechanical System - "Coolant")
2. Release the residual pressure in fuel line. (Refer to Fuel Delivery System - "Release Residual Pressure in Fuel Line")
3. Remove the delivery pipe. (Refer to Fuel Delivery System - "Delivery Pipe")
4. Remove the Engine Coolant Temperature Sensor (ECTS) (A) after removing the bolt.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Removal and Installation / Removal illustration

Engine Coolant Temperature Sensor (ECTS) #2 - Cylinder Block
1. Drain the coolant. (Refer to Engine Mechanical System - "Coolant")
2. Remove the alternator. (Refer to Engine Electrical System - "Alternator")
3. Disconnect the Engine Coolant Temperature Sensor (ECTS) connector (A).

Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Removal and Installation / Removal illustration

4. Remove the ECTS (A) after removing the bolt.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Engine Coolant Temperature Sensor (ECTS) to the specified torque.
• If the ECTS is dropped, it may cause internal damage. (Do not reuse)
• Apply the engine coolant to the O-ring.

Engine Control / Fuel System — Engine Control System / Engine Coolant Temperature Sensor (ECTS) / Removal and Installation / Installation illustration

• Install the ECTS by pushing it into the mounting hole when installing it. At this time do not impact the sensor.
2. Refill the coolant. (Refer to Engine Mechanical System - "Coolant")

Heated Oxygen Sensor (HO2S) Specification

Specification
Item
Specification
Front
Rear
Operating voltage (V)
12
Heater resistance (Ω)
2.5 (Room temperature)
3.1 (Room temperature)
Heater capacity (W)
8.1
7.3
Current consumption (A)
1.2
Maximum 1.01

Heated Oxygen Sensor (HO2S) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Components and Components Location / Component Location illustration

1. Front Heated Oxygen Sensor (HO2S)
1-a. 39.2 - 49.0 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)
2. Rear HO2S
2-a. 39.2 - 49.0 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)

Heated Oxygen Sensor (HO2S) Description and Operation

Description
• Heated Oxygen Sensor (HO2S), consisting of zirconium and alumina, is installed on both upstream and downstream of the Manifold Catalytic Converter (MCC) to detect the air/fuel ratio and send it to the Engine Control Module (ECM).
• In order that this sensor operates properly, the temperature of the sensor tip must be higher than 370°C (698°F). For this reason, a heater controlled by the ECM duty signal, is built into the sensor.
• When the exhaust gas temperature is lower than the specified value, the heater warms the sensor tip. Front

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Description and Operation / Description illustration

Rear

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Description and Operation / Description illustration

Heated Oxygen Sensor (HO2S) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data analysis : Check the system input/output values (Data Analysis → System Selection → Engine)
Information    
Refer to the KDS screen for operating conditions and details
Component Inspection
1. Disconnect the Heated Oxygen Sensor (HO2S) connector.
2. Measure the resistance between the HO2S terminals. Front Heated Oxygen Sensor

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / On Vehicle Inspection illustration

Terminal
Function
Wire Color
2
Heater ( + )
Grey
5
Heater ( - )
White

Rear Heated Oxygen Sensor

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / On Vehicle Inspection illustration

Terminal
Function
Wire Color
3
Heater ( + )
Red
4
Heater ( - )
White

3. Check that the resistance is within the specification.
Item
Specification
Front
Rear
Heater resistance (Ω)
2.5 (Room temperature)
3.1 (Room temperature)

Heated Oxygen Sensor (HO2S) Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Heated Oxygen Sensor (HO2S) socket
09392 - 1Y100

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Special Service Tool illustration

Used for removing / installing the Heated Oxygen Sensor (HO2S)
※ SST 09392 - 2H100 also can be used

Removal
Caution    
Wait for the engine to cool down to avoid burns from the high temperatures of the exhaust system.
Front Heated Oxygen Sensor (HO2S)
1. Disconnect the battery negative ( - ) terminal.
2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
3. Disconnect the front Heated Oxygen Sensor (HO2S) connector (A).

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration

4. Separate the front HO2S connector (A) by pulling it in the direction of the arrow from the bracket.

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration

5. Separate the front HO2S wiring (A) after removing the wiring fixing clip (B).

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration

6. Remove the front HO2S (A) by using SST (09392 - 1Y100 or 09392 - 2H100).
Tightening torque : 39.2 - 49.0 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration

Rear Heated Oxygen Sensor (HO2S)
1. Disconnect the battery negative ( - ) terminal.
2. Remove the engine cover. (Refer to Engine Mechanical System - "Engine Cover")
3. Disconnect the rear Heated Oxygen Sensor (HO2S) connector (A).

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration

4. Separate the rear HO2S connector (A) by pulling it in the direction of the arrow from the bracket.

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration

5. Remove the engine room under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")
6. Separate the rear HO2S wiring (A) from the holders.

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration

7. Remove the rear HO2S (A).
Tightening torque : 39.2 - 49.0 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)

Engine Control / Fuel System — Engine Control System / Heated Oxygen Sensor (HO2S) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Heated Oxygen Sensor (HO2S) to the specified torque.
• If the HO2S is dropped, it may cause internal damage. (Do not reuse)
• Do not use oil components such as cleaners, sprays, or greases on the sensing part and connector as it may degrade the performance of HO2S.
• Be careful not to damage the HO2S from the exhaust system (exhaust manifold, catalytic converter, etc.).
2. Reset the ECM adaptive value after replacing the heated oxygen sensor. (S/W Management → Engine → Resetting Adaptive Values)
Information    
Refer to the KDS screen for operating conditions and details

Knock Sensor (KS) Specification

Specification
Item
Specification
Capacitance (pF)
850 - 1,150
Resistance (MΩ)
Below 1
Frequency range (kHz)
5 - 22

Knock Sensor (KS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Knock Sensor (KS) / Components and Components Location / Component Location illustration

1. Knock Sensor (KS)
1-a. 18.6 - 23.5 N·m (1.9 - 2.4 kgf·m, 13.7 - 17.4 lb·ft)

Knock Sensor (KS) Description and Operation

Description
• The Knock Sensor (KS) detects vibration when knocking and transmits to the Engine Control Module (ECM).
• The knocking sensor outputs a knocking signal when knocking, and the ECM that receives the signal to prevent the knocking by perceiving the timing of ignition. If there is no knocking signal, ECM which controls the timing of ignition continuously to ensure the optimum torque and fuel efficiency.

Engine Control / Fuel System — Engine Control System / Knock Sensor (KS) / Description and Operation / Description illustration

Knock Sensor (KS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data analysis : Check the system input/output values (Data Analysis → System Selection → Engine)
Information    
Refer to the KDS screen for operating conditions and details

Knock Sensor (KS) Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Disconnect the Knock Sensor (KS) connector (A).

Engine Control / Fuel System — Engine Control System / Knock Sensor (KS) / Removal and Installation / Removal illustration

3. Remove the KS (A) after removing the bolt.
Tightening torque : 18.6 - 23.5 N·m (1.9 - 2.4 kgf·m, 13.7 - 17.4 lb·ft)

Engine Control / Fuel System — Engine Control System / Knock Sensor (KS) / Removal and Installation / Removal illustration

4. Separate the KS connector (A) by pulling it in the direction of the arrow from the bracket.

Engine Control / Fuel System — Engine Control System / Knock Sensor (KS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Knock Sensor (KS) to the specified torque.
• If the KS is dropped, it may cause internal damage. (Do not reuse)

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) Specification

Specification
Item
Specification
Rated voltage (V)
5
Operating voltage (V)
4.5 - 5.5
Output voltage (V)
0.5 - 4.5

[Manifold Absolute Pressure Signal]
Pressure
Output Voltage (V)
kPa
kg/cm²
psi
10
0.1
1.45
0.5
40
0.4
5.80
0.913
80
0.8
11.60
1.465
120
1.2
17.40
2.017
160
1.6
23.20
2.569
200
2.0
29.00
3.120
220
2.2
31.90
3.396
240
2.4
34.80
3.672
280
2.8
40.61
4.224
300
3.0
43.51
4.5

[Intake Air Temperature Signal]
Temperature
Resistance (Ω)
°C
°F
-41 to -39
-41.8 to -38.2
41,518 - 47,652
-21 to -19
-5.8 to -2.2
14,112 - 15,810
-1 to 1
30.2 to 33.8
5,450 - 5,980
19 to 21
66.2 to 69.8
2,346 - 2,529
24 to 26
75.2 to 78.8
1,930 - 2,070
39 to 41
102.2 to 105.8
1094.6 - 1188.7
59 to 61
138.2 to 141.8
551.39 - 607.05
79 to 81
174.2 to 177.8
297.75 - 331.77
99 to 101
210.2 to 213.8
170.72 - 192.32
119 to 121
246.2 to 249.8
103.12 - 117.30
129 to 131
264.2 to 267.8
81.52 - 93.15
149 to 151
300.2 to 303.8
52.55 - 60.55

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) / Components and Components Location / Component Location illustration

1. Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS)
1-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) Description and Operation

Description
Manifold Absolute Pressure Sensor (MAPS)
• Manifold Absolute Pressure Sensor (MAPS) is a speed-density type sensor that senses absolute pressure of the Intake Manifold.
• MAPS transfers the analog signal proportional to the pressure to the Engine Control Module (ECM).
• By using this signal, the ECM calculates the intake air amount and engine speed.
Intake Air Temperature Sensor (IATS)
• Intake Air Temperature Sensor (IATS) is included inside MAPS and detects the intake air temperature.
• To calculate precise air quantity, correction of the air temperature is needed because air density varies according to the temperature. So the ECM uses not only MAPS signal but also IATS signal.
• This sensor has a Negative Temperature Coefficient (NTC) Thermistor and it's resistance changes in reverse proportion to the temperature.

Engine Control / Fuel System — Engine Control System / Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) / Description and Operation / Description illustration

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data analysis : Check the system input/output values (Data Analysis → System Selection → Engine)
Information    
Refer to the KDS screen for operating conditions and details

Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Disconnect the Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) connector (A).

Engine Control / Fuel System — Engine Control System / Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) / Removal and Installation / Removal illustration

3. Remove MAPS & IATS (A) after removing the bolt.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Engine Control / Fuel System — Engine Control System / Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Manifold Absolute Pressure Sensor & Intake Air Temperature Sensor (MAPS & IATS) to the specified torque.
• If the MAPS & IATS is dropped, it may cause internal damage. (Do not reuse)

Oil Pressure & Oil Temperature Sensor (OPTS) Specification

Specification
Item
Specification
Supply voltage (V)
5
Operating voltage (V)
4.75 - 5.25
Operating temperature [°C (°F)]
-40 to 155 (-40 to 311)

[Pressure Characterisitics]
Item
Specification
Pressure
bar
0.5
1
6
11
MPa
0.05
0.1
0.6
1.1
psi
7.25
14.50
87.02
159.54
Output voltage (V)
0.26 - 0.34
0.46 - 0.54
2.46 - 2.54
4.46 - 4.54

[Temperature Characterisitics]
Temperature
Resistance (kΩ)
°C
°F
-40
-40
125.53 - 136.70
-30
-22
93.26 - 104.65
-20
-4
63.89 - 71.23
-10
14
41.80 - 46.52
0
32
26.83 - 30.07
10
50
17.13 - 19.23
20
68
11.13 - 12.48
25
77
9.00 - 10.11
30
86
7.369 - 8.279
40
102
4.89 - 5.50
50
122
3.34 - 3.76
60
140
2.32 - 2.61
70
158
1.63 - 1.84
80
176
1.17 - 1.32
90
194
0.86 - 0.97
100
212
0.64 - 0.72
110
230
0.48 - 0.54
120
248
0.37 - 0.41
130
266
0.28 - 0.32
140
284
0.22 - 0.25
150
302
0.17 - 0.20
160
320
0.14 - 0.16

Oil Pressure & Oil Temperature Sensor (OPTS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Oil Pressure & Oil Temperature Sensor (OPTS) / Components and Components Location / Component Location illustration

1. Oil Pressure & Temperature Sensor (OPTS)
1-a. 35.3 - 38.2 N·m (3.6 - 3.9 kgf·m, 26.0 - 28.2 lb·ft)

Oil Pressure & Oil Temperature Sensor (OPTS) Description and Operation

Description
• Oil Pressure & Temperature Sensors (OPTS) measures oil pressure and temperature and send the information to Engine Control Module (ECM).
• Send the pressure information to the ECM by measuring the oil pressure and temperature discharged from the oil pump, and the ECM adjusts the proportional control valve to maintain the discharged pressure according to the rpm.

Engine Control / Fuel System — Engine Control System / Oil Pressure & Oil Temperature Sensor (OPTS) / Description and Operation / Description illustration

Oil Pressure & Oil Temperature Sensor (OPTS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Data analysis : Check the system input/output values (Data Analysis → System Selection → Engine)
Information    
Refer to the KDS screen for operating conditions and details
Component Inspection
1. Measure the resistance between the OPTS terminals 1 and 4 after disconnecting the connector.

Engine Control / Fuel System — Engine Control System / Oil Pressure & Oil Temperature Sensor (OPTS) / On Vehicle Inspection illustration

Terminal
Function
1
Sensor ground
4
Sensor

2. Check that the resistance is within the specification.
Temperature
Resistance (kΩ)
°C
°F
-40
-40
125.53 - 136.70
-30
-22
93.26 - 104.65
-20
-4
63.89 - 71.23
-10
14
41.80 - 46.52
0
32
26.83 - 30.07
10
50
17.13 - 19.23
20
68
11.13 - 12.48
25
77
9.00 - 10.11
30
86
7.369 - 8.279
40
102
4.89 - 5.50
50
122
3.34 - 3.76
60
140
2.32 - 2.61
70
158
1.63 - 1.84
80
176
1.17 - 1.32
90
194
0.86 - 0.97
100
212
0.64 - 0.72
110
230
0.48 - 0.54
120
248
0.37 - 0.41
130
266
0.28 - 0.32
140
284
0.22 - 0.25
150
302
0.17 - 0.20
160
320
0.14 - 0.16

Oil Pressure & Oil Temperature Sensor (OPTS) Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Remove the engine room under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")
3. Disconnect the Oil Pressure & Temperature Sensor (OPTS) connector (A).

Engine Control / Fuel System — Engine Control System / Oil Pressure & Oil Temperature Sensor (OPTS) / Removal and Installation / Removal illustration

4. Remove the OPTS (A).
Tightening torque : 35.3 - 38.2 N·m (3.6 - 3.9 kgf·m, 26.0 - 28.2 lb·ft)

Engine Control / Fuel System — Engine Control System / Oil Pressure & Oil Temperature Sensor (OPTS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Oil Pressure & Temperature Sensor (OPTS) to the specified torque.
• If the OPTS is dropped, it may cause internal damage. (Do not reuse)
• Be careful not to get engine oil and/or coolant into the OPTS connector.
• When engine oil and/or coolant flow into the OPTS connector, replace it with a new one. (Do not reuse.)

RCV Control Solenoid Valve Specification

Specification
Item
Specification
Operating voltage (V)
9 - 16
Resistance (Ω)
28.3 - 31.1

RCV Control Solenoid Valve Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / RCV Control Solenoid Valve / Components and Components Location / Component Location illustration

1. Air Cleaner
1-a. 7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
1-b. 2.9 - 4.9 N·m (0.3 - 0.5 kgf·m, 2.2 - 3.6 lb·ft, 26.0 - 43.4 lb·in)
2. RCV Control Solenoid Valve

RCV Control Solenoid Valve Description and Operation

Description
• The Recirculation Control Valve (RCV) operates the RCV actuator which controls the by-pass passage of the turbocharger compressor.
• If the throttle is closed while the engine is on, the turbocharger boost pressure increases rapidly so the impeller near the compressor causes a crashing noise.
• To prevent the noise, the Engine Control Module (ECM) opens the bypass path to release the pressure from the compressor. Therefore, the crashing sound is no longer existed by maintaining the pressure of the boost.

Engine Control / Fuel System — Engine Control System / RCV Control Solenoid Valve / Description and Operation / Description illustration

RCV Control Solenoid Valve On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Actuation test : Checking the system operation condition (Data Analysis → System Selection → Engine → Actuation Test →TCI Bypass Valve(Turbo Only))
Information    
Refer to the KDS screen for operating conditions and details
Component Inspection
1. Disconnect the battery negative ( - ) terminal.
2. Disconnect the Recirculation Control Valve (RCV) connector (A).

Engine Control / Fuel System — Engine Control System / RCV Control Solenoid Valve / On Vehicle Inspection illustration

3. Measure resistance between the terminals.
Specified value (Ω) : 28.3 - 31.1

RCV Control Solenoid Valve Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Remove the air cleaner assembly. (Refer to Engine Mechanical System - "Air Cleaner")
3. Disconnect the RCV control solenoid valve connector (A).

Engine Control / Fuel System — Engine Control System / RCV Control Solenoid Valve / Removal and Installation / Removal illustration

4. Separate the Recirculation Control Valve (RCV) (A) by pulling it in the direction of the arrow from the bracket.

Engine Control / Fuel System — Engine Control System / RCV Control Solenoid Valve / Removal and Installation / Removal illustration

5. Remove the RCV (A) after separating RCV hoses (B).

Engine Control / Fuel System — Engine Control System / RCV Control Solenoid Valve / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• If the Recirculation Control Valve (RCV) is dropped, it may cause internal damage. (Do not reuse)
• Be careful not to get foreign matter into the RCV.

Variable Force Solenoid (VFS) Specification

Specification
Item
Specification
Operating voltage (V)
10 - 16
Coil resistance (Ω)
5.5 - 6.2 [20°C (68°F)]

Variable Force Solenoid (VFS) Components and Components Location

Component Location

Engine Control / Fuel System — Engine Control System / Variable Force Solenoid (VFS) / Components and Components Location / Component Location illustration

1. Variable Force Solenoid (VFS) - Exhaust
1-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
2. VFS - Intake
2-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

Variable Force Solenoid (VFS) Description and Operation

Description
• Variable Force Solenoid (VFS) supplies the engine oil to the cam phaser or cuts the engine oil from the cam phaser in accordance with the Engine Control Module (ECM) Pulse Width Modulation (PWM) control signal, the cam phaser which varies the cam phase by using the hydraulic force of the engine oil.
• The delivered oil rotates the rotor connected to the camshaft of the cam phaser and rotates the camshaft to the engine rotating direction (intake advanced / exhaust retarded) or the opposite direction (intake retarded / exhaust advanced) to change the phase angle of the cam.

Engine Control / Fuel System — Engine Control System / Variable Force Solenoid (VFS) / Description and Operation / Description illustration

Variable Force Solenoid (VFS) On Vehicle Inspection

On Vehicle Inspection
Diagnosis With the KDS
1. The engine control system can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
(1) Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS (Refer to DTC guide when fault code is found)
(2) Actuation test : Checking the system operation condition (Data Analysis → System Selection → Engine → Actuation Test → Oil Control Valve - Intake Bank1 / Oil Control Valve - Exhaust Bank1 (Option))
Information    
Refer to the KDS screen for operating conditions and details

Variable Force Solenoid (VFS) Removal and Installation

Removal
1. Disconnect the battery negative ( - ) terminal.
2. Disconnect the Variable Force Solenoid (VFS) connector (A). [Intake]

Engine Control / Fuel System — Engine Control System / Variable Force Solenoid (VFS) / Removal and Installation / Removal illustration

[Exhaust]

Engine Control / Fuel System — Engine Control System / Variable Force Solenoid (VFS) / Removal and Installation / Removal illustration

3. Remove the VFS (A) after removing the bolts.
Tightening torque : 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
[Intake]

Engine Control / Fuel System — Engine Control System / Variable Force Solenoid (VFS) / Removal and Installation / Removal illustration

[Exhaust]

Engine Control / Fuel System — Engine Control System / Variable Force Solenoid (VFS) / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Install the Variable Force Solenoid (VFS) to the specified torque.
• If the VFS is dropped, it may cause internal damage. (Do not reuse)
• When installing the VFS, apply the engine oil to the O-ring (A).

Engine Control / Fuel System — Engine Control System / Variable Force Solenoid (VFS) / Removal and Installation / Installation illustration

Other information:

Kia K4 (CL4) 2025-2026 Service Manual: Forward Collision-Avoidance Assist (FCA) (Sensor Fusion)

Basic function The Forward Collision-Avoidance Assist (FCA) system in your Kia K4 is designed to proactively monitor the road ahead. By utilizing advanced sensor fusion technology, it can detect vehicles, motorcyclists, pedestrians, or cyclists in your path.

Kia K4 (CL4) 2025-2026 Service Manual: Front seat adjustment for power seat:

The Kia K4 features intuitive power-operated driver's seat adjustments, controlled via the switches mounted on the outboard side of the seat cushion. Before operating your Kia K4, always configure your seat to a position that provides effortless access to the steering wheel, foot pedals, and all instrument panel controls to ensure safe and attentive driving.

Contents

Categories

Copyright © 2026 Kia K4 Manuals ⏱ 0.0435