Contents:
| General Service Information |
| 1.
|
Protect the vehicle's protective painted surfaces and internal parts with work covers (seat
covers) or
tape (if damaged by tools) to prevent damage.
|
Before closing the engine hood, check the engine room for any tools or parts
left.
|
|
| 2.
|
At the same time as checking the defective part, determine the cause of the failure, determine
whether it
is necessary to remove or disassemble, and then work in the order of the workshop manual.
In order to prevent mis-assembly and to facilitate assembly work, punch marks or coincidence
marks are
applied to areas that do not adversely affect the function or appearance. When disassembling
parts with a
large number of parts and similar parts, arrange them so as not to be confused during assembly.
| 1) |
Arrange the removed parts in order.
|
| 2) |
Distinguish between replacement parts and reusable parts.
|
| 3) |
When replacing bolts and nuts, be sure to use designated standard products.
|
|
| 3.
|
Special tools must be used for work instructing the use of special tools, as the parts may be
damaged or
damaged if the work is performed by using tools other than special tools.
|
| 4.
|
Reusable parts below must be replaced with new ones.
| 6) |
Split pin
|
|
| 5.
|
Part
| 1) |
When replacing a new part, be sure to use genuine Kia parts.
|
| 2) |
Use repair parts and the enclosed sets and kits.
|
| 3) |
Parts supplied as maintenance parts may differ from parts assembled in a
vehicle for the
unification of parts, so check the parts catalog carefully before performing
maintenance work.
|
|
| 6.
|
Be sure to turn the ignition switch "OFF" and disconnect the battery negative ( - ) cable
before
replacing or repairing electrical system parts.
|
| 7.
|
Be careful not to contact fuel and oil with rubber parts and hoses.
|
Inspection of Battery Terminals And Wiring
| 1.
|
Check that the battery terminals are solid.
|
| 2.
|
Check that the battery terminals and wiring are not corroded by battery electrolyte.
|
| 3.
|
Check the battery terminals and wiring for open circuits or the potential to open the circuit.
|
| 4.
|
Check the insulation and sheath of the wiring for damage, cracks, and deterioration of quality.
|
| 5.
|
Check if the terminals of the battery terminals are in contact with other metal parts (car body
or other
parts).
|
| 6.
|
Make sure that the ground bolt and the body are in full contact.
|
| 7.
|
Check the wiring connection.
|
| 8.
|
Make sure that the wiring does not come into contact with sharp edges or hot parts (exhaust
manifold,
muffler, etc.) on the vehicle body.
|
| 9.
|
Make sure that the wiring is secured with sufficient clearance from rotating parts such as
cooling fans
and drive belts.
|
| 10.
|
Make sure that the wiring has an adequate vibration margin between vibration parts such as
engines and
fixed parts such as vehicle bodies.
|
Inspection of Fuse
| 1.
|
Check whether the fuse holder firmly secures the fuse.
|
| 2.
|
Verify that the fuse capacity is appropriate for each circuit.
|
| 3.
|
Inspect the fuse for any signs of damage or malfunction.
|
The fuse has an inspection contact, allowing you to check its condition without
removing it. To
test the fuse, connect one contact of a test lamp to one side of the fuse (one
at a time) and ground
the other contact. If the lamp lights up, the fuse is proper. (Make sure the
ignition switch is in
the correct position to allow current to flow through the fuse circuit.)
|
|
| 4.
|
If the fuse is blown or damaged, refer to the electrical circuit diagram and inspect the
components
connected to the fuse.
|
| 5.
|
If no abnormalities are found in the components, thoroughly check the wiring circuit for any
interference
or damage.
|
| 6.
|
When replacing a fuse, always use one with the specified rated capacity.
|
Using a fuse with a higher capacity than the specified one may cause damage to
components or even
a fire.
|
|
Inspection of Electrical System
| 1.
|
Be sure to turn the ignition switch "OFF" and disconnect the battery negative ( - ) cable
before
replacing or repairing electrical system parts.
|
Disconnecting the battery negative ( - ) cable during system check will clear
the error code
stored in the engine control module (ECM).
Read the fault code before disconnecting the battery negative ( - ) cable.
|
|
| 2.
|
Fix the wiring with a clamp to prevent stretching.
|
| 3.
|
If the wiring contact with the edge or end of the part, wrap the interference part with tape to
protect
it from damage.
|
| 4.
|
When assembling vehicle parts, be careful not to damage the wiring.
|
| 5.
|
Be careful not to throw or cause shock to relays, sensors, electrical parts.
|
| 6.
|
ECM and relays are easy to get damaged by overheating.
At temperatures above 176°F (80°C), disconnect electrical parts before inspection work.
|
| 7.
|
Loose connector connection may cause failure, so make sure that the connector is properly
connected.
|
| 8.
|
When disconnecting the connector, hold the connector body.
|
| 9.
|
When disconnecting the lockable connector, release the lock as shown below.
|
| 10.
|
When installing the lockable connector, push it in until a "click" sound is heard.
|
| 11.
|
When checking the energization or voltage of a connector terminal with a circuit tester, insert
the probe
from the harness side.
If the connector is of a sealed type, be careful not to damage the insulation of the wiring,
and insert
the probe through the hole in the rubber sheath until the probe touches the terminal.
|
| 12.
|
Select appropriate wiring as shown in the table below to prevent overloading the wiring.
Recommended
|
SAE Standard NO.
|
Allowable current
|
Engine Room
|
The other parts
|
0.3mm²
|
AWG 22
|
-
|
5A
|
0.5mm²
|
AWG 20
|
7A
|
13A
|
0.85mm²
|
AWG 18
|
9A
|
17A
|
1.25mm²
|
AWG 16
|
12A
|
22A
|
2.0mm²
|
AWG 14
|
16A
|
30A
|
3.0mm²
|
AWG 12
|
22A
|
40A
|
5.0mm²
|
AWG 10
|
31A
|
54A
|
|
Other information:
Kia K4 (CL4) 2025-2026 Service Manual: LCD display
The high-resolution LCD display in your Kia K4 serves as a central hub for essential vehicle information, driving statistics, and system settings. You can seamlessly navigate and customize the various LCD display modes using the intuitive steering wheel-mounted control buttons, allowing you to stay informed while keeping your focus on the road.
LCD display control
Kia K4 (CL4) 2025-2026 Service Manual: Intelligent Speed Limit Assist (ISLA):
The Intelligent Speed Limit Assist (ISLA) system in the Kia K4 enhances your driving awareness by integrating data from detected traffic signs and the onboard navigation system. It proactively informs you of current speed restrictions to help you maintain compliance with local traffic laws.
TIP
The Intelligent Speed Limit Assist may have limited operational capacity or accuracy if utilized in regions outside of the original market for which the Kia K4 was designed.