Kia K4: Power Train / Cooling System Replacement

Inspection
Radiator hoses
1. Check radiator hoses for the following:
(1) Improper attachment
(2) Leaks
(3) Cracks
(4) Damage
(5) Loose connections
(6) Chafing
(7) Deterioration
Coolant level
1. Check the coolant level in the coolant reservoir. Make sure it is between the "MAX" mark and "MIN" mark.
2. If the coolant level in the coolant reservoir is at or below the "MIN" mark, add coolant to bring it between the "MIN" and "MAX" marks, then inspect the cooling system for leaks.
Coolant quality
1. Remove the radiator cap.
2. Check if there are any excessive deposits of rust or scale around the radiator cap sub-assembly and radiator filler hole. Also, the coolant should be free of oil. If excessively dirty, clean the coolant passage and replace the coolant.
3. Install the radiator cap.
Engine Coolant Refilling And Air Bleeding
[G 2.0 MPI NU(ATKINSON)]
Caution    
• Never remove the pressure cap when the engine is hot.
• Serious scalding could be caused by hot coolant under high pressure escaping from the radiator.
Note    
• Be sure to add coolant according to the lntegrated Thermal Management Module (ITM) coolant refill method.
• When replenishing coolant, be careful not to spill on the belt, electrical devices.
Coolant replacement and air bleed using KDS.
1. Make sure the engine and radiator are cool enough to touch.
2. Remove the pressure cap (A).

Maintenance — Power Train / Cooling System / Replacement / [G 2.0 MPI NU(ATKINSON)] illustration

3. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
4. Remove the drain plug (A) and drain the engine coolant.

Maintenance — Power Train / Cooling System / Replacement / [G 2.0 MPI NU(ATKINSON)] illustration

5. Tighten the radiator drain plug securely after draining the engine coolant.
6. Clean the reservoir tank after drain the coolant inside the reservoir tank.
7. Install the coolant refill tank on the radiator and then add the mixture of anti-freeze and water (45 - 50%) (except for North America, Europe and China: 55 - 60%)
Caution    
Fill coolant as far as possible with engine and all power supplies shut off.
Coolant capacity Approx. 6.0 ℓ (1.59 U.S.gal., 6.34 U.S.qt., 5.28 lmp.qt.)
Note    
• Press the radiator upper/lower hoses to allow air to escape easily.
• Use only genuine antifreeze.
• Do not mix antifreeze/coolant from different brands.
• Do not add any anti-rust.
• Use only distilled water when mixing antifreeze with water.
• For best corrosion protection, the coolant concentration must be maintained year-round at 45% (except for North America, Europe and China: 55%) minimum. Coolant concentrations less than 45% (except for North America, Europe and China: 55%) may not provide sufficient protection against corrosion or freezing.
• Coolant concentrations greater than 60% will impair cooling efficiency and are not recommended.
8. Connect the KDS to the data link connector and then IG- ON.
9. Perform the Integrated Thermal Management Module (ITM) coolant filling mode" using KDS. (S/W Management → Engine Control → Integrated Thermal Module Coolant Filling Mode)
10. Start the engine.
Note    
Keep the engine idle.
11. Fill the reservoir tank to the "MAX" (or "FULL") line with coolant and tighten the pressure cap.
Note    
When the coolant temperature reaches 90°C (194° F) or 20 minutes have passed since the engine start, check the coolant level in the reservoir tank and replenish.
12. Stop the Integrated Thermal Management Module (ITM) cooling water filling mode" using KDS.
13. Run the engine until enough coolant circulates.
14. Check the Coolant capacity in the reservoir tank, refill it to the "MAX" (or "FULL") line.
15. Install the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
Coolant replacement and manual air bleed. No KDS.
1. Make sure the engine and radiator are cool enough to touch.
2. Disconnect the battery negative ( - ) terminal.
3. Remove the pressure cap (A).

Maintenance — Power Train / Cooling System / Replacement / [G 2.0 MPI NU(ATKINSON)] illustration

4. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
5. Remove the drain plug (A) and drain the engine coolant.

Maintenance — Power Train / Cooling System / Replacement / [G 2.0 MPI NU(ATKINSON)] illustration

6. Tighten the radiator drain plug securely after draining the engine coolant.
7. Clean the reservoir tank after drain the coolant inside the reservoir tank.
8. Disconnect the Integrated Thermal Management Module (ITM) connector (A).

Maintenance — Power Train / Cooling System / Replacement / [G 2.0 MPI NU(ATKINSON)] illustration

Note    
• When disconnecting the Integrated Thermal Management Module (ITM) connector (A), make sure the engine and all power are off.
• Be careful not to apply static electricity or other voltage to the Integrated Thermal Management Module (ITM).
• Do not bring magnetic objects such as magnets close to the Integrated Thermal Management Module (ITM).
9. Install the coolant refill tank on the radiator and then add the mixture of anti-freeze and water (45 - 50%) (except for North America, Europe and China: 55 - 60%)
Caution    
Fill coolant as far as possible with engine and all power supplies shut off.
Coolant capacity Approx. 6.0 ℓ (1.59 U.S.gal., 6.34 U.S.qt., 5.28 lmp.qt.)
Note    
• Press the radiator upper/lower hoses to allow air to escape easily.
• Use only genuine antifreeze.
• Do not mix antifreeze/coolant from different brands.
• Do not add any anti-rust.
• Use only distilled water when mixing antifreeze with water.
• For best corrosion protection, the coolant concentration must be maintained year-round at 45% (except for North America, Europe and China: 55%) minimum. Coolant concentrations less than 45% (except for North America, Europe and China: 55%) may not provide sufficient protection against corrosion or freezing.
• Coolant concentrations greater than 60% will impair cooling efficiency and are not recommended.
10. Start the engine.
Note    
Keep the engine idling.
11. Fill the reservoir tank to the "MAX" (or "FULL") line with coolant and tighten the pressure cap.
Note    
20 minutes have passed since the engine start, check the coolant level in the reservoir tank and replenish.
12. Connect the Integrated Thermal Management Module (ITM) connector (A) after turn off the engine.

Maintenance — Power Train / Cooling System / Replacement / [G 2.0 MPI NU(ATKINSON)] illustration

Note    
• When connecting the integrated thermal management module (ITM) connector, water or oil must be completely removed from the connector and no foreign matters should be entered.
• When replacing the integrated thermal management module (ITM) connector, be sure to use the specified connector.
13. After starting the engine for 5 seconds, turn off the engine.
Information    
• This procedure is repeated 3 times.
• Check the check engine light OFF after starting the engine in the 4th procedure.
14. After starting the engine, check the sound of the Integrated Thermal Management Module (ITM) operation.
15. Run the engine until cooling water is circulating properly.
16. Check the Coolant capacity in the reservoir tank, refill it to the "MAX" (or "FULL") line.
17. Install the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
18. Install the pressure cap (A).

Maintenance — Power Train / Cooling System / Replacement / [G 2.0 MPI NU(ATKINSON)] illustration

[G 1.6 T-GDI GAMMA II]
Caution    
• Do not remove the pressure cap when the engine is hot.
• Serious scalding could be caused by hot coolant under high pressure escaping from the reservoir tank.
Note    
• Be sure to add coolant according to the ITM coolant refill method.
• When replenishing coolant, be careful not to spill on the belt, electrical devices.
By using the KDS, replace coolant and bleed air out.
1. Make sure the engine and radiator are cool to the touch.
2. Remove the pressure cap (A).

Maintenance — Power Train / Cooling System / Replacement / [G 1.6 T-GDI GAMMA II] illustration

3. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
4. Remove the drain plug (A) and drain the coolant.

Maintenance — Power Train / Cooling System / Replacement / [G 1.6 T-GDI GAMMA II] illustration

5. After draining the coolant, re-tighten the drain plug.
6. Drain coolant and inside the reservoir tank, and then clean it.
7. Fill mixture of the antifreeze and water (45 - 60%) as much as possible through the reservoir tank inlet while IG-OFF.
Coolant capacity : Approximately 7.2 ℓ (1.90 U.S gal, 7.61 U.S.qt., 6.34 Imp.qt.)
Note    
• Press the radiator upper/lower hoses to allow air to escape easily.
• For best cooling performance, use a antifreeze that meets vehicle specifications. Genuine antifreeze is an antifreeze whose quality and performance are guaranteed by Kia.
• Do not mix antifreeze/coolant from different brands.
• Do not add any anti-rust.
• Use only distilled water when mixing antifreeze with water.
• If the concentration of coolant is less than 45%, corrosion or freezing may occur, and if the concentration of coolant is more than 60%, the cooling effect may be reduced, so the concentration of coolant shall be maintained at 50 to 55%.
8. Connect KDS in IG-ON state.
9. Perform the Integrated Thermal Management Module (ITM) coolant filling mode" using KDS.
Information    
Refer to the KDS screen for operating conditions and details
10. Start the engine.
11. Fill the reservoir tank with coolant.
Note    
When the coolant temperature reaches 90°C (194° F) or 20 minutes have passed since the engine start, check the coolant level in the reservoir tank and replenish.
12. Stop the Integrated Thermal Management Module (ITM) cooling water filling mode" using KDS.
13. Run the engine until enough coolant circulates.
14. Check the Coolant capacity in the reservoir tank, refill it to the "MAX" (or "FULL") line.
15. Install the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
When using KDS is not possible, replace the coolant and bleed the air out.
1. Make sure the engine and radiator are cool to the touch.
2. Remove the pressure cap (A).

Maintenance — Power Train / Cooling System / Replacement / [G 1.6 T-GDI GAMMA II] illustration

3. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
4. Remove the drain plug (A) and drain the coolant.

Maintenance — Power Train / Cooling System / Replacement / [G 1.6 T-GDI GAMMA II] illustration

5. After draining the coolant, re-tighten the drain plug.
6. Drain coolant and inside the reservoir tank, and then clean it.
7. Remove the air cleaner assembly. (Refer to Intake and Exhaust System - "Air Cleaner")
8. Disconnect the Integrated Thermal Management Module (ITM) connector (A).

Maintenance — Power Train / Cooling System / Replacement / [G 1.6 T-GDI GAMMA II] illustration

Note    
• When disconnecting the Integrated Thermal Management Module (ITM) connector (A), make sure the engine and all power are OFF.
• Be careful not to apply static electricity or other voltage to the Integrated Thermal Management Module (ITM).
• Do not bring magnetic objects such as magnets close to the Integrated Thermal Management Module (ITM).
9. Fill mixture of the antifreeze and water (45 - 60%) as much as possible through the reservoir tank inlet.
Coolant capacity : Approximately 7.2 ℓ (1.90 U.S gal, 7.61 U.S.qt., 6.34 Imp.qt.)
Note    
• Press the radiator upper/lower hoses to allow air to escape easily.
• For best cooling performance, use a antifreeze that meets vehicle specifications. Genuine antifreeze is an antifreeze whose quality and performance are guaranteed by Kia.
• The coolant concentration should be kept at least 45-60% to prevent corrosion. If the coolant concentration is less than 45-60%, there is a risk of corrosion and freezing.
• It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
• Do not mix different brands of antifreeze and coolant.
• Do not add any anti-rust.
• When mixing coolant and water, use distilled water instead of tap water.
10. Start the engine.
11. Fill the reservoir tank with coolant.
Note    
20 minutes have passed since the engine start, check the coolant level in the reservoir tank and replenish.
12. Connect the Integrated Thermal Management Module (ITM) connector after turning OFF the engine.

Maintenance — Power Train / Cooling System / Replacement / [G 1.6 T-GDI GAMMA II] illustration

13. Repeat the engine ON/OFF and check the engine warning lamp OFF.
(1) Wait for 5 seconds with engine ON and then turn OFF the engine.
(2) Repeat the step (1) 3 times.
(3) Check the engine warning lamp OFF when engine is turned ON for the fourth time.
14. Run the engine until enough coolant circulates.
15. Check the Coolant capacity in the reservoir tank, refill it to the "MAX" (or "FULL") line.
16. Remove the air cleaner assembly. (Refer to Intake and Exhaust System - "Air Cleaner")
17. Install the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")

Other information:

Kia K4 (CL4) 2025-2026 Service Manual: Storage compartments

The Kia K4 interior is designed with several convenient storage compartments to organize small items for both the driver and passengers: For your security, it is highly recommended not to store high-value items in any vehicle storage compartments to avoid potential theft. Always ensure that compartment lids are fully closed while the Kia K4 is in motion.

Kia K4 (CL4) 2025-2026 Service Manual: Owner maintenance

The following comprehensive lists outline the essential vehicle checks and inspections that should be performed by the owner or an authorized Kia dealer at the indicated intervals. Diligent adherence to these checks is vital to ensure the safe, dependable, and efficient operation of your Kia K4 throughout its service life. Should you identify any adverse conditions or irregularities, please bring your Kia K4 to the attention of an authorized Kia dealer as soon as possible for expert evaluation.

Categories

Copyright © 2026 Kia K4 Manuals ⏱ 0.0099