Kia K4: Emission Control System / Exhaust Emission Control System

Contents:

Catalytic Converter Components and Components Location

Component

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Components and Components Location / Component illustration

1. Front Heated Oxygen Sensor (HO2S)
1-a. 39.2 - 49.0 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)
2. Warm-up Catalytic Converter (WCC) Upper Bracket
2-a. 39.2 - 44.1 N·m (4.0 - 4.5 kgf·m, 28.9 - 32.5 lb·ft)
3. Rear HO2S
3-a. 39.2 - 49.0 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft)
4. Front Muffler
4-a. 39.2 - 58.8 N·m (4.0 - 6.0 kgf·m, 28.9 - 43.4 lb·ft)
5. WCC Lower Bracket
5-a. 49.0 - 53.9 N·m (5.0 - 5.5 kgf·m, 36.2 - 39.8 lb·ft)
6. WCC
6-a. 35.3 - 41.2 N·m (3.6 - 4.2 kgf·m, 26.0 - 30.4 lb·ft)
7. Gasket

Catalytic Converter Description and Operation

Description
• The catalytic converter of the gasoline engine is a three way catalyst. It oxidizes carbon monoxide and hydrocarbons (HC), and separates oxygen from the oxides of nitrogen (NOx).
• Carbon monoxide, hydrocarbons and nitrogen oxide in exhaust gas are converted into less hazardous substances through the chemical reaction of oxidation reduction.

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Description and Operation / Description illustration

Catalytic Converter Removal and Installation

Video Guide
Note    
• This video was created using 3D graphics to help understand the vehicle maintenance manual.
• There may be some differences from actual vehicles.
• The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
• Check the KDS Guide for detailed information on how to use the KDS.
• Check the manual for detailed maintenance procedures.
• Unauthorized reproduction, distribution, or sharing of this video is prohibited.
Underbody Catalytic Converter (UCC) Replacement (Click to play)Emission Control System — Exhaust Emission Control System / Catalytic Converter / Removal and Installation / Video Guide illustration

Video: Underbody Catalytic Converter (UCC) Replacement

Removal
Caution    
To prevent burns due to the high heat, work when the temperature of the engine and the surrounding area is sufficiently low.
Warm-up Catalytic Converter (WCC)
1. Disconnect the battery negative ( - ) terminal.
2. Disconnect the rear Heated Oxygen Sensor (HO2S) connector (A).

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Removal and Installation / Removal illustration

3. Separate the rear HO2S connector (A) by pulling it in the direction of the arrow from the bracket.

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Removal and Installation / Removal illustration

4. Remove the front HO2S. (Refer to Engine Control/Fuel System - "Heated Oxygen Sensor (HO2S)")
5. Remove the Warm-up Catalytic Converter (WCC) upper bracket (A) by removing the bolts.
Tightening torque : 39.2 - 44.1 N·m (4.0 - 4.5 kgf·m, 28.9 - 32.5 lb·ft)

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Removal and Installation / Removal illustration

6. Remove the WCC nuts (A).
Tightening torque : 35.3 - 41.2 N·m (3.6 - 4.2 kgf·m, 26.0 - 30.4 lb·ft)

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Removal and Installation / Removal illustration

7. Remove the front muffler. (Refer to Engine Mechanical System - "Muffler")
8. Remove the wiring clip (A) from the WCC lower mounting bracket.

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Removal and Installation / Removal illustration

9. Remove the lower mounting bracket (A) by removing the bolts.
Tightening torque : 49.0 - 53.9 N·m (5.0 - 5.5 kgf·m, 36.2 - 39.8 lb·ft)

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Removal and Installation / Removal illustration

10. Remove the WCC (A).

Emission Control System — Exhaust Emission Control System / Catalytic Converter / Removal and Installation / Removal illustration

Underbody Catalytic Converter (UCC)
1. Remove the Catalytic converter & center muffler assembly. (Refer to Engine Mechanical System - "Muffler")
Installation
Warm-up Catalytic Converter (WCC)
1. Install in the reverse order of removal.
Note    
Install the Warm-up Catalytic Converter (WCC) to the specified torque.
Underbody Catalytic Converter (UCC)
1. Install in the reverse order of removal.
Note    
Install the Underbody Catalytic Converter (UCC) to the specified torque.

Other information:

Kia K4 (CL4) 2025-2026 Service Manual: Lane Keeping Assist (LKA)

When operating your Kia K4 at speeds above a certain threshold, the Lane Keeping Assist (LKA) system actively monitors road lane markings and edges. Designed to enhance your driving experience, Lane Keeping Assist can provide proactive steering assistance to help prevent your Kia K4 from unintentionally drifting out of its lane. Furthermore, the system is engineered to provide an alert if it detects that the vehicle is departing from its lane without the driver engaging the turn signal.

Kia K4 (CL4) 2025-2026 Service Manual: Forward Attention Warning malfunction and limitations

NOTE In the event of a system error, the following alerts will be displayed on your Kia K4 LCD screen. For comprehensive troubleshooting, please refer to the "malfunction and limitations" documentation for the affected system: "Check forward attention warning system" (Indicates a potential sensor or software issue) "Forward attention warning disabled.

Contents

Categories

Copyright © 2026 Kia K4 Manuals � 0.0133