|
•
|
This video was created using 3D graphics to help understand the vehicle
maintenance manual.
|
|
•
|
There may be some differences from actual vehicles.
|
|
•
|
The location and repair procedures of the parts may vary depending on vehicle
model, model year,
region, and specifications.
|
|
•
|
Check the KDS Guide for detailed information on how to use the KDS.
|
|
•
|
Check the manual for detailed maintenance procedures.
|
|
•
|
Unauthorized reproduction, distribution, or sharing of this video is
prohibited.
|
|
Wide Angle Camera
(Click to play)
Video: Wide Angle Camera Calibration
Tolerance Calibration Outline
Tolerance calibration compensates for the error margins of surround view video that occur due to the
installation
tolerance when the four cameras that comprise the SVM system are installed.
Tolerance calibration must be performed when the following
actions are
performed.
|
–
|
When conducting a body task that causes the focus of the wide angle camera
changes.
|
|
–
|
When replacing the ADAS Parking ECU.
|
|
–
|
When a failure code (System Out of Calibration) occurs.
|
|
Tolerance Calibration Environments
|
SVM calibration tool is required to perform tolerance calibration as shown below.
|
Manual Tolerance Calibration Procedure
| 1.
|
Prepare in advance as below.
|
–
|
Confirm that the car hood, trunk and doors are closed.
|
|
–
|
Close the door after getting in on the driver side.
|
|
–
|
Unfold outside rear view mirrors.
|
|
–
|
Shift the gear to the 'N'.
|
|
–
|
During the advance preparation, do not install exhaust inhaler or other
equipment that may block
the view of rearview cameras.
|
|
–
|
Engage foot brake or Electronic Parking Brake (EPB) to hold vehicle in place.
|
|
| 2.
|
Before entering tolerance calibration mode, to check normal operation of SVM ECU and cameras,
perform the
following.
|
–
|
Check that initial setting screen of SVM is displayed. (Front view image +
surround view image
when shifted to N)
|
|
–
|
Check that front, rear, left and right images of surround view monitor are
properly displayed.
|
|
–
|
If images are properly displayed, enter tolerance calibration mode. Otherwise,
if images are
abnormally displayed or are not displayed, replace relevant part.
|
|
| 3.
|
Install two calibration scales, two calibration reference line boards, and four calibration
target boards
around the vehicle by referring to the manual provided with the tools.
|
•
|
There are two types (Type A & B) and the base line should
be matched to vehicle type.
|
|
•
|
Accurately set the location (distance/angle) of the center of
white and black calibration
board as this is the reference point.
|
|
| (1)
|
Align the vehicle in a straight line and install the SVM ruler on the front and
rear tires in the
direction of the arrow.
|
| (2)
|
To align the center point of the vehicle, install the calibration ruler by
moving it from side to
side so that the calibration ruler dimensions below the tires on the right and
left sides are the
same.
|
•
|
Be careful not to crease when installing the
SVM ruler.
|
|
•
|
The measurements on both sides should be the
same.
|
|
[RH]
[LH]
[LH]
[RH]
|
•
|
If the user is equipped with tires of different
dimensions than the
specification, the results of the SVM tolerance
correction work may not be accurate.
|
|
•
|
The dimensions of the front and rear tires may
be different.
|
|
|
| (3)
|
The SVM reference line should be installed according to the end point of SVM
ruler.
|
•
|
Align the right-front wheel center of the tire
with the base line on the SVM
reference line.
|
|
•
|
There are two types(Type A & B) and the
Base line should be matched to
vehicle type.
|
|
•
|
Base line margin of error should be 3 cm (1.1
in.)
|
|
•
|
Measure the margin of error at the end of the
baseline (A).
|
|
|
Install it in the same way on the left hand side.
|
|
| (4)
|
After installing the calibration ruler and the calibration reference line,
verify that the left
and right calibration reference lines are installed parallel to each other.
|
•
|
If the distance between left and right is the
same back and forth, the
calibration reference line is normally
installed.
|
|
•
|
The error range of the calibration reference
line left/right distance shall be
299 to 301 cm (117.7 ~ 118.5 in).
|
|
|
| (5)
|
Install the SVM target on the SVM reference line.
|
•
|
The angle between the SVM calibration reference
line and the SVM calibration
target shall be 90 degrees.
|
|
•
|
Rotation error when aligning vehicle should be
within 1° to left/right.
|
|
|
|
| 4.
|
Maintain IG ON with vehicle stopped, check that the gear is in P, and engage parking brake even
on flat
ground.
|
| 5.
|
Work is carried out with the parking/view button ON.
|
| 6.
|
Perform the order below with the KDS.
(S/W Management → Advanced Driver Assistance System Parking → SVM Calibration Mode)
|
Refer to the KDS screen for operating conditions and details.
|
|
•
|
Before matching calibration points: "+" green light flashes.
|
|
•
|
When clicking [OK] after matching calibration points: "+" red
light ON.
|
|
•
|
After matching the four front calibration points, click the OK
button and click the
Update SVM button to move to the next camera calibration.
|
|
•
|
Perform calibration tasks in the order of the front -> rear
-> left -> right
camera.
|
|
|
| 7.
|
Check the vehicle and the calibration line on the monitor screen to see if the calibration has
been
completed normally and press the [OK] button.
If calibration has not been properly performed, click [Cancel] and reenter calibration points.
[AVN Monitor Screen]
|
|
•
|
Do not fold and store the calibration ruler, calibration reference line,
calibration target.
|
|
•
|
Clean any debris found on the SVM rulers, SVM reference lines or the target
point before storing
them in their container.
|
|
•
|
The calibration ruler, calibration reference line, and calibration target are
rolled into the
enclosed cylindrical roll and stored in a dedicated storage bag.
|
|
Automatic Tolerance Calibration While Driving
| 1.
|
Check the following conditions for normal operation of the automatic tolerance calibration
while driving.
|
–
|
Check whether the front/rear/left/right sides of the SVM top view are displayed
normally.
|
|
–
|
If the image is not displayed normally, check the related parts.
|
|
|
•
|
It shall be carried out in manual mode as possible and shall be carried out
only in unavoidable
cases, such as the absence of equipment.
|
|
| 1.
|
Perform the order below with the KDS.
(S/W Management → Advanced Driver Assistance System Parking → SVM Self-calibration mode)
|
| 2.
|
Check the steering angle (A), vehicle speed (B) and SVM top view (C) are displayed normally on
the dealer
mode screen.
|
•
|
After entering the automatic tolerance correction while
driving, the diagnostic device
entry mode can be terminated by manipulating the MAP and MEDIA
buttons.
|
|
•
|
The operating conditions for automatic tolerance correction
while driving are steering
wheel steering angle -5 ~ 5° and vehicle speed1 ~ 50 km/h (0.6 ~
31 mph)
|
|
•
|
When a vehicle is out of the steering angle or vehicle speed
the steering wheel symbol
(A) and the speed meter symbol (B) are displayed in red and if
the vehicle meets the
requirements, they will be displayed in green.
|
|
•
|
Tolerance calibration is performed only when both the steering
wheel symbol and the
speedometer symbol are marked in green.
|
|
|
| 3.
|
Move a vehicle to road and select the start button (A) on the dealer mode screen to perform the
tolerance
calibration while maintaining constant speed.
|
•
|
When the steering wheel angle and speed conditions are met, a
green border is expressed
on each symbol and calibration is initiated.
|
|
•
|
If the top view is inconsistent after the calibration is
completed, press the start
button (A) to re-run.
|
|
|
•
|
Ideal road conditions for tolerance calibration while driving.
|
|
–
|
The center lane of a one-way three-lane road with markers such
as arrows, letters, etc.
on the road surface.
|
|
–
|
A flat road which is not uphill/downhill and without slope.
|
|
•
|
Factors that can cause temporary stop or delay of tolerance
calibration while driving.
|
|
–
|
Road/environment without feature points.
|
|
–
|
Nighttime, rainfall, snowfall environment.
|
|
–
|
Painted indoor parking lot.
|
|
•
|
Correctable camera distortion limit.
|
|
|
| 4.
|
The calibration progress rate while driving can be checked with the status bar (A).
|
•
|
The indicator (C) on the dealer mode screen blinks in green
during calibration.
|
|
•
|
It is possible to drive freely without restrictions on the
steering angle and vehicle
speed while the calibration is in progress after entering the
calibration.
|
|
•
|
The calibration time takes about 2 minutes under ideal
conditions.
|
|
•
|
When a start button (D) is pressed during calibration, it can
resume from the point of
stop after pause.
|
|
•
|
If the stop button (B) is pressed during calibration, it can be
stopped, and if the start
button (D) is pressed again, it can be started from the
beginning.
|
|
•
|
When the status bar is filled fully, calibration is completed
and the signal light (C) is
displayed in green.
|
|
|
| 5.
|
Press the Home button (C) at the end of the calibration function. (The AVNT monitor
automatically reboots
at the end of the calibration function)
|
•
|
Do not operate the audio/AVNT monitor button if a pop-up
'Update in progress' occurs
during reboot.
|
|
•
|
To check the calibration results, we recommend a flat and
precisely divided parking lot.
|
|
•
|
If the calibration result is not satisfied, perform the
automatic tolerance calibration
again while driving.
|
|
–
|
If additional calibration is needed after the saved calibration
result, select the start
button (A) to perform it again.
|
|
–
|
After deleting the saved result by selecting the stop button
(B), you can perform a new
calibration by selecting start button (A).
|
|
|
| 6.
|
Check the calibration result when the calibration is completed.
Criteria for judging the calibration result : The distortion of the mating surface area at a
distance of
1.8 m (5.9 ft) from a vehicle must be within 8 cm (3.15 in).
|