| Airbag Module Disposal Procedure |
When scrapping a vehicle equipped with an airbag system such as an airbag or seat Belt Pretensioner (BPT), the
airbag must be deployed first. When deploying the airbag, it must be deployed by a skilled technician, and the
used
airbag cannot be reused, so it must not be installed in another vehicle.
|
•
|
If an undeployed airbag is accidentally deployed, it may cause serious injury,
so it must be
disposed after deployment.
|
|
•
|
Deployment of the airbag must be performed on a level ground with no risk
elements.
|
|
•
|
An explosion sound occurs when the airbag is deployed, perform it in a place
where there is no
damage to the surroundings.
|
|
•
|
Smoke may occur when the airbag is deployed, perform the deployment of the
airbag in area with
good ventilation and no smoke detector nearby.
|
|
•
|
The airbag is very hot after deploying, so wait at least 30 minutes and let it
cool before
touching it.
|
|
•
|
Keep the deployed airbag away from water.
|
|
|
•
|
When scrapping a vehicle, the airbag should, in principle, be deployed while
installed in the
vehicle. Do not remove the airbag except unavoidable circumstances.
|
|
•
|
If the airbag is removed from the vehicle due to airbag replacement (accident
repair, warranty
repair, etc.), refer to the relevant manual and deploy it outside the vehicle.
(Deploying the airbag
inside the vehicle may cause damage to the vehicle.)
|
|
•
|
Do not disassemble the airbag.
|
|
•
|
Be careful not to damage the airbag.
|
|
•
|
Be careful not to drop the airbag.
|
|
•
|
When deploying the airbag, deploy it at least 7 m (22.97 ft.) away from the
airbag.
|
|
•
|
When deploying the airbag, always use the special tool and perform it in a
place without
electrical noise.
|
|
|
•
|
Wash hands thoroughly with soap after deploying, repacking, and disposal of the
airbag.
|
|
•
|
Always wear protective gloves, goggles and earplugs when deploying the airbag.
|
|
Tools and Equipment Required for Disposal of Airbag Modules
Illustration
|
Name
|
Possible Cause
|
|

|
Gloves
|
|
|

|
Goggles
|
|
|

|
Earplugs
|
|
|

|
2 tires with wheels
|
(Top / Bottom)
|
|

|
3 tires without the wheels
|
(Middle)
|
|

|
Rope strap / Ratchet strap
|
(Use for connecting the airbag equipment and tires according to the deployment instructions)
|
|

|
12 V battery
|
|
Deployed inside the vehicle
| 1.
|
Disconnect the battery negative (-) terminal.
|
After disconnecting the battery negative ( - ) terminal, wait at least 3
minutes and 30 seconds.
|
|
| 2.
|
Make sure the airbag is securely installed.
|
| 3.
|
Prepare to deploy the airbag or seat belt pretensioner as follows.
| (1)
|
Disconnect the airbag or seat belt pretensioner connector to be deployed.
|
| (2)
|
Connect the deployment adapter to the airbag or seat belt pretensioner.
|
•
|
For the Driver Airbag (DAB), disconnect the
connector, connect the deployment
adapter, and then reinstall it on the steering
wheel.
|
|
•
|
When using the deployment adapter, use it
appropriately according to the
deployment airbag.
|
|
–
|
DAB, PAB, CAB, BPT (0K57A - 3U100A)
|
|
|
|
| 4.
|
Workers should be at least 7 meters away from the vehicle.
|
| 5.
|
Connect the Special Service Tool (0957A - 34100A) to the deployment adapter and then connect it
to the
external battery.
| (2)
|
Airbag deployment tool (0957A - 34100A)
|
| (3)
|
Deployment adapter
|
|
| 6.
|
Activate the switch of the airbag deployment tool to deploy the airbag.
| (1)
|
When connecting to an external battery normally , POWER ON (1) is turned on.
|
| (2)
|
If READY (2) button illuminates while pressing READY (2) button, press DEPLOY
(3) button to
deploy the airbag.
|
When the airbag is deployed, loud noise is generated, visually
confirmed, and after rapid
inflation, it contracts slowly.
|
|
|
| 7.
|
Place the deployed airbag in a sturdy plastic bag and sealed securely, then dispose it.

|
Deployment outside of the vehicle
| 1.
|
After spreading the rope (A) on the floor in a cross shape, put the tire (B) equipped with the
wheel on
the floor.

|
| 2.
|
Connect the deployment adapter (A) to the airbag or pretensioner.

|
•
|
For the Driver Airbag (DAB), disconnect the connector, connect
the deployment adapter,
and then reinstall it on the steering wheel.
|
|
•
|
When using the deployment adapter, use it appropriately
according to the deployment
airbag.
|
|
–
|
DAB, PAB, CAB, BPT (0K57A - 3U100A)
|
|
|
| 3.
|
Fix the airbag / pretensioner (A) to the wheel.
Airbag

|
If the airbag deployment surface faces downward instead of upward, the airbag
may spring up and
cause serious injury to the worker.
|
Pretensioner

|
Install the end of the piston tube of the anchor pretensioner, facing the
floor.
|
|
| 4.
|
After putting the three waste tires (A), put the tire (B) with the wheel on it.
|
| 5.
|
Fix the tire by using the ratchet strap (C).

|
| 6.
|
After connecting the battery, connect the airbag deployment tool (0957A - 34100A) to the
deployment
adapter (0K57A - 3U100A).

|
| 7.
|
Activate the switch of the airbag deployment tool to deploy the airbag.
| (1)
|
When connecting to an external battery normally , POWER ON (1) is turned on.
|
| (2)
|
If READY (2) button illuminates while pressing READY (2) button, press DEPLOY
(3) button to
deploy the airbag.
|

|
When the airbag is deployed, loud noise is generated, visually confirmed, and
after rapid
inflation, it contracts slowly.
|
|
| 8.
|
Place the deployed airbag in a sturdy plastic bag and sealed securely, then dispose it.

|
Damaged Airbag (Undeployed Airbag) Disposal Procedure
| 1.
|
Disconnect the battery negative (-) terminal.
|
After disconnecting the battery negative ( - ) terminal, wait at least 3
minutes and 30 seconds.
|
|
| 2.
|
If necessary, remove the damaged airbag (undeployed airbag) from the vehicle.
|
For airbags with wires, twist the wires to create a short circuit.
|
|
–
|
For airbags with lead wires, twist the wires to create a short circuit.
|
|
| 3.
|
Place the removed airbag in a sturdy plastic bag or box and sealed tightly, and then dispose
it.
|
If storing the damaged airbag individually without return or disposal, write a
warning message on
the plastic bag.
|
|
Other information:
Kia K4 (CL4) 2025-2026 Service Manual: Power window lock button
The primary driver can instantly disable the localized power window switches located on the rear passengers’ doors by engaging the master safety toggle switch. Pressing the power window lock button down into its locked position (fully depressed) intercepts the signal path to prevent rear cabin occupants from manipulating the glass regulators of your Kia K4.
Kia K4 (CL4) 2025-2026 Service Manual: Forward Attention Warning malfunction and limitations
NOTE
In the event of a system error, the following alerts will be displayed on your Kia K4 LCD screen. For comprehensive troubleshooting, please refer to the "malfunction and limitations" documentation for the affected system:
"Check forward attention warning system" (Indicates a potential sensor or software issue)
"Forward attention warning disabled.