Kia K4: Charging System / Battery On Vehicle Inspection

On Vehicle Inspection

Engine Electrical System — Charging System / Battery / On Vehicle Inspection illustration

Battery Visual and Basic Inspection
1. Check the battery terminal corrosion and connection.
2. Check the battery leakage or swelling.
3. Check the case for damage.
Alternator Charging Current Inspection
1. Check the alternator charging current. (Refer to Charging System - "Alternator")
Vehicle Parasitic Current Inspection [Using an Ammeter]
1. Turn all electric devices OFF, and then turn the IG OFF.
2. Close all doors except the engine hood, and then lock all doors.
– Disconnect the connector from the hood switch to prevent it from being operated.
3. Wait until the main system of the vehicle goes into sleep mode.
Note    
For an accurate measurement of a vehicle parasitic current, all electrical systems should go to sleep mode. (It takes at least one hour or at most one day.) However, an approximate vehicle parasitic current can be measured after 10 - 20 minutes.
4. Connect an ammeter between the battery negative ( - ) terminal and the negative ( - ) cable terminal, and then disconnect the battery cable ( - ) terminal slowly.

Engine Electrical System — Charging System / Battery / On Vehicle Inspection illustration

Note    
• Be careful not to let the lead wire of the ammeter come off the battery terminal and the cable so that the battery is not initialized.
• If the battery is initialized due to disconnection of lead wire of ammeter from the battery cable or terminal, reconnect the battery and start the engine, or measure from the first step after the IG is on for more than 10 seconds.
• To prevent battery initialization in advance, follow the procedure below.
1) Connect the jumper cable between the battery ( - ) terminal and the cable ( - ) terminal first.
2) Disconnect the negative ( - ) battery terminal.
3) Connect the ammeter in parallel to the jumper cable.
4) Disconnect the jumper cable and check the parasitic current value of the ammeter.
5. Check the parasitic current value of the ammeter.
• If the parasitic current exceeds the limit value, remove the fuse one by one and measure it to find the problem circuit.
• Re-measure the parasitic current and find the problem unit by removing the units connected to the problem circuit one by one.
Limit value (mA) : Below 50 (after 10 - 20 min.)
[[Using the Clamp Type Ammeter]
1. Turn all electric devices OFF, and then turn the IG OFF.
2. Close all doors except the engine hood, and then lock all doors.
– Disconnect the connector from the hood switch to prevent it from being operated.
3. Wait until the main system of the vehicle goes into sleep mode.
Note    
For an accurate measurement of a vehicle parasitic current, all electrical systems should go to sleep mode. (It takes at least one hour or at most one day.) However, an approximate vehicle parasitic current can be measured after 10 - 20 minutes.
4. Install the clamp type ammeter on battery negative ( - ) terminal

Engine Electrical System — Charging System / Battery / On Vehicle Inspection illustration

Note    
• When using a clamp type ammeter, use an ammeter that can measure mA. If not, it is difficult to measure the correct parasitic current.
• When ( - ) sign appears on the ammeter of the clamp type, install the ammeter in the opposite direction.
5. Check the parasitic current value of the ammeter.
• If the parasitic current exceeds the limit value, remove the fuse one by one and measure it to find the problem circuit.
• Re-measure the parasitic current and find the problem unit by removing the units connected to the problem circuit one by one.
Limit value (mA) : Below 50 (after 10 - 20 min.)
Battery Performance Inspection
1. Measure the performance of the battery by using the battery tester and battery load tester.
Note    
• Check that the battery positive ( + ) and negative ( - ) terminals are properly connected.
• Do not disconnect the battery while the engine is running.
Battery Voltage Inspection
1. If it is within 20 minutes since the engine is stopped, turn on the ignition switch and operate the electric devices (headlamp, blower motor, rear defogger) for 60 seconds to get rid of residual voltage.
2. Turn the IG OFF.
3. Measure the voltage between the negative ( - ) terminal and battery positive ( + ) terminal of the battery.
Specified voltage (V) : approximately 12.5 - 12.9 [20°C (68°F)]
4. If the measured value is below the specified voltage, charge the battery.
AGM Battery Charging
Information    
Follow the charging method(DIN 41772) defined by German Standards Association (DIN).
– I (Constant current) : It is also called the constant current method. this method is charging by maintaining regularly the current from start the charging to complete.
– U(Constant voltage) : It is also called the constant voltage method. this method is charging by maintaining regularly the voltage from start the charging to complete.
– W(Taper current) : It is called also the single current method. this method is a type of constant current method, and is charging by decreasing the current in charging step by step.
1. Check the state of charge of the battery, and charge the battery if required.
How to charge IU or WU IU or WU charging voltage (V) :14.7 [20 - 30°C (68 - 86°F)] Approximately 24 hours Minimum charging voltage (V) : 14.4 [20°C (68°F)] Maximum charging voltage (V) : 14.8 [20°C (68°F)] A capacity of 10% of the charging current is recommended (e.g. 80 Ah : 100% = 8.0 A of charging current)
Warning    
• Do not charge over the 15.2 V, and not quick charge.
• Do not open or remove the cap on the top of the AGM battery.
• Since explosive gas is formed in each cell when charging the battery, any actions that may cause ignition such as fire, sparks, light rays, smoking, etc. during or immediately after charging the battery are prohibited.
• Do not open the circuit while the battery is charging as it will generate the spark, keep away from nearby flammable material.
Note    
• The temperature of the battery shall be maintained at approximately 20 - 30°C (68 - 86°F) during charging.
• If the battery sensor is charged while connected to the battery, the sensor may not accurately detect the state of the battery. Therefore, when the battery is fully charged, use it after about 10 hours (stabilizing time of the battery) at room temperature. Otherwise, it will result in a fault code or the Alternator Management System (AMS) function may not work.

Other information:

Kia K4 (CL4) 2025-2026 Service Manual: Rear occupant alert (ROA) system

The advanced Rear Occupant Alert (ROA) system integrated into your vehicle is a vital driver assistance feature configured to monitor the rear passenger cabin. This sub-system actively reduces the risk of a child, infant, vulnerable passenger, or family pet being inadvertently left behind in the vehicle when the driver exits. Environmental Sensor Optimization Protocol: To ensure the underlying ultrasonic interior sensors function with maximum accuracy, make sure that all side passenger windows and the sunroof assembly are completely closed whenever the ROA framework is operational.

Kia K4 (CL4) 2025-2026 Service Manual: Blind-Spot Collision-Avoidance Assist (BCA):

The Blind-Spot Collision-Avoidance Assist (BCA) system is designed to detect vehicles approaching in your blind spots and alert you to potential hazards using both visual and audible warnings. If the system calculates a high risk of collision during an intended lane change, the Kia K4 can provide supplemental braking assistance to help you avoid an accident.

Categories

Copyright © 2026 Kia K4 Manuals � 0.0063