Contents:
Description and Operation
|
•
|
The alternator consists of a rotor, stator, rectifier, brush, regulator, bearing, and a pulley.
|
|
•
|
A diode integrated in alternator acts as a rectifier. Rectifier circuit containing diodes
converts
alternating current (AC) into direct current (DC) and supply it to the alternator B terminal.
|
|
•
|
Engine Control Module (ECM) controls the amount of electricity generated by charging control,
discharging
control and normal control according to the battery status and the electricity usage of the
vehicle.
|
| Alternator Management System (AMS) |
|
•
|
Alternator Management System (AMS) improves fuel efficiency and manages the battery charging
state by
checking vehicle driving conditions, electric load, and battery state.
|
|
•
|
The Engine Control Module (ECM) controls generating voltage by duty cycle (charging control,
discharging
control, normal control) based on the battery conditions and vehicle operating conditions.
|
|
•
|
The ECM performs discharging control during acceleration to consume battery power and lighten
the load on
the alternator. The ECM performs charging control during deceleration to charge the battery.
|
On Vehicle Inspection

| 1.
|
The charging system can be more quickly diagnosed for problems with the KDS. (Refer to "DTC
guide")
| (1)
|
Self Diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS
(Refer to DTC guide when fault code is found.)
|
| (2)
|
Data Analysis : Checking the system input/output data state
|
| (3)
|
Actuation Test : Checking the system operation condition
|
| (4)
|
S/W Management : Controlling other features including system option setting and
zero point
adjustment
|
|
| 2.
|
Check the continuity of the fuse.
Alternator fuse (A)

Battery fuse (A)

|
| 3.
|
Check the battery terminal for corrosion and connection.

Check List
|
•
|
Check the alternator B+ terminal condition
|
|
•
|
Check the alternator B+ terminal tightening nut
|
|
•
|
Check the battery positive ( + ) and negative ( - ) terminal
condition
|
|
•
|
Check the battery positive ( + ) and negative ( - ) terminal
tightening nut
|
|
•
|
Check if the mounting bolt for the body of the vehicle
connected to ( - ) terminal of the
battery is tightened
|
|
•
|
Check the engine room fuse box & relay box positive ( + )
cable condition
|
|
•
|
Check the engine room fuse box & relay box positive ( + )
cable tightening nut
|
|
•
|
Inspect the ground fault caused by the paint
|
|
|
| 4.
|
Check the connector connection, contact defect, bending, corrosion, deformation or damage.
|
| 5.
|
Check the condition of engine ground cable (A) and tight to specified torque.
|
Tightening torque :
10.8 - 13.7 N·m (1.1 - 1.4 kgf·m, 8.0 - 10.1 lb·ft)
|

|
| 6.
|
Check the condition of transaxle ground cable (A) and tight to specified torque.
|
Tightening torque :
26.5 - 32.4 N·m (2.7 - 3.3 kgf·m, 19.5 - 23.9 lb·ft)
|

|
| 7.
|
Inspect the drive belt.

|
Replace the belt when the belt cracks and damages.
|
|
| 8.
|
Check the charging system components
|
•
|
Battery(Refer to Charging
System - "Battery")
|
|
•
|
Battery Sensor(Refer to
Charging System - "Battery Sensor")
|
|
•
|
Alternator(Refer to
Charging System - "Alternator")
|
|
•
|
Engine Control Module (ECM)(Refer to Engine Control/Fuel System - "Engine
Control Module
(ECM)")
|
|
Alternator Specification
Item
|
Specification
|
Rated output (V, A)
|
13.5, 130
|
Speed in use (rpm)
|
1,000 - 18,000
|
Pulley type
|
Overrunning Alternator Pulley (OAP)
|
Alternator Components and Components Location
1. Drive Belt 2. Drive Belt
Tensioner 2-a. 34.3
- 41.2 N·m (3.5 - 4.2 kgf·m, 25.3 - 30.4 lb·ft) 2-b. 18.6 - 23.5 N·m (1.9 - 2.4 kgf·m, 13.7 -
17.4
lb·ft)
|
3. Alternator 3-a. 18.6 - 24.5 N·m (1.9 -
2.5
kgf·m, 13.7 - 18.1 lb·ft) 3-b. 29.4 - 41.2 N·m (3.0 - 4.2 kgf·m, 21.7 - 30.4 Ib·ft)
|
1. Cap 2. Pulley 3. Rear Cover 3-a.
3.0 - 4.4
N·m (0.31 - 0.45 kgf·m, 2.2 - 3.3 lb·ft, 26.9 - 39.1 lb·in) 4. Brush & Regulator
Assembly 4-a. 3.0 -
4.4 N·m (0.31 - 0.45 kgf·m, 2.2 - 3.3 lb·ft, 26.9 - 39.1 lb·in)
|
5. Front Bracket 6. Rotor Assembly 7.
Stator 8. Rear Bracket 8-a. 4.5 - 5.5 N·m (0.46 - 0.56 kgf·m, 3.3 - 4.1 lb·ft, 39.9 - 48.6
lb·in)
|
Alternator Description and Operation
|
•
|
The alternator consists of a rotor, stator, rectifier, brush, regulator, bearing, and pulley.
|
|
•
|
A diode integrated in alternator acts as a rectifier. Rectifier circuit containing diodes
converts
alternating current (AC) into direct current (DC) and supply it to the alternator B terminal.
|
|
•
|
The Engine Control Module (ECM) controls generating voltage by duty cycle (charging control,
discharging
control, normal control) based on the battery conditions and vehicle operating conditions.
|
Alternator Removal and Installation
| 1.
|
Disconnect the battery negative ( - ) terminal.
|
| 2.
|
Remove the drive belt tensioner.
(Refer to Engine Mechanical System - "Drive Belt
Tensioner")
|
| 3.
|
Separate the return hose and pipe bracket (A) after removing the bolts.
|
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
| 4.
|
Open the alternator B terminal cable cap (A).
|
| 5.
|
Remove the alternator B terminal cable (A) after removing the nut.
|
Tightening torque :
18.6 - 24.5 N·m (1.9 - 2.5 kgf·m, 13.7 - 18.1 lb·ft)
|
|
| 6.
|
Disconnect the A/C compressor connector (A).
|
| 7.
|
Disconnect the alternator connector (A) and remove the wiring fixing clip (B).
|
| 8.
|
Remove the alternator (A) after removing the bolts.
|
Tightening torque :
29.4 - 41.2 N·m (3.0 - 4.2 kgf·m, 21.7 - 30.4 Ib·ft)
|
|
| 1.
|
Install in reverse order of removal.
|
•
|
Install the alternator to the specified torque.
|
|
•
|
If the alternator is dropped, it may cause internal damage. (Do
not reuse)
|
|
•
|
Before installing the alternator, hit the alternator mounting
bolt (A) with a plastic
hammer and move it to the outside of the draft bushing (B).
|
|
|
Alternator Disassembly and Reassembly
Tool Name / Number
|
Illustration
|
Description
|
Alternator pulley removal / installation wrench 09373 - 27000
|
|
Used for removing / installing alternator pulley
|
| 1.
|
Remove the Overrunning Alternator Pulley (OAP) cap (A).
|
| 2.
|
Remove the OAP pulley (A) by using SST (09373 - 27000).
|
Tightening torque :
75.5 - 81.4 N·m (7.7 - 8.3 kgf·m, 55.7 - 60.0 lb·ft)
|
|
| 3.
|
Remove the rear cover (A) after removing the nuts.
|
Tightening torque :
3.0 - 4.4 N·m (0.31 - 0.45 kgf·m, 2.2 - 3.3 lb·ft, 26.9 - 39.1 lb·in)
|
|
| 4.
|
Remove the brush & regulator assembly (A) after removing the bolts.
|
Tightening torque :
3.0 - 4.4 N·m (0.31 - 0.45 kgf·m, 2.2 - 3.3 lb·ft, 26.9 - 39.1 lb·in)
|
|
| 5.
|
Remove the rectifier assembly (A) after removing the bolt and nuts.
|
Tightening torque :
3.0 - 4.4 N·m (0.31 - 0.45 kgf·m, 2.2 - 3.3 lb·ft, 26.9 - 39.1 lb·in)
|
|
| 6.
|
Dissolve the stator leads (A) by using the soldering gun.
|
| 7.
|
Remove the front bracket (A) after removing the bolts.
|
Tightening torque :
4.5 - 5.5 N·m (0.46 - 0.56 kgf·m, 3.3 - 4.1 lb·ft, 39.9 - 48.6 lb·in)
|
|
| 8.
|
Remove the rotor assembly (A).
|
| 9.
|
Remove the stator (A) from the rear bracket assembly.
|
| 1.
|
Reassemble in the reverse order of disassembly.
|
•
|
Install the alternator assembly to the specified torque.
|
|
•
|
Be careful not to damage the components when installing the
brush and regulator assembly.
|
|
|
Alternator Inspection
| 1.
|
Check for continuity between each slip ring (A). It is normal if there is continuity.
|
| 2.
|
Check that there is continuity between the slip ring and the rotor (B) or rotor shaft (C). It
is normal
if there is no continuity.

|
| 3.
|
If any of item 1 and 2 above is defective, replace the rotor.
|
| 1.
|
Check for the continuity between each pair of stator coil (A). It is normal if there is
continuity.

|
| 2.
|
Check for the continuity between the stator coil and the core. It is normal if there is no
continuity.
|
| 3.
|
If any one of items 1 and 2 above is defective, replace the stator.
|
Battery Specification
Item
|
Specification
|
Model type
|
AGM60L-DIN
|
Capacity [20HR/5HR] (AH)
|
60 / 48
|
Cold cranking ampere (A)
|
640 (SAE / EN)
|
Reserve capacity (Min)
|
100
|
Specific gravity
|
1.29 - 1.31
|
Voltage (V)
|
12
|
Battery Size
Model Type
|
Capacity [20HR/5HR] (AH)
|
Size [mm (in.)]
|
Width
|
Length
|
Height
|
Total Height
|
AGM60L-DIN
|
60 / 48
|
240 - 242 (9.45 - 9.52)
|
173 - 175 (6.81 - 6.88)
|
166 - 168 (6.54 - 6.61)
|
187 - 190 (7.36 - 7.48)
|

|
Battery Components and Components Location
1. Battery Negative ( - ) Terminal 1-a. 7.8
- 9.8
N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft) 2. Battery Positive ( + ) Terminal 2-a. 7.8 - 9.8 N·m
(0.8 - 1.0
kgf·m, 5.8 - 7.2 lb·ft) 3. Clamp 3-a. 8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)
|
4. Insulated Pad 5. Battery 6. Battery
Tray 6-a. 8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)
|
Battery Description and Operation
The Absorbent Glass Material (AGM) battery controls the electrolyte by absorbing the electrolyte into the
absorbent glass fiber separator inside the battery, and the valve installed on the top of the battery minimizes
gas
release.
| Battery Label Information |
| 1.
|
Battery specifications
|
–
|
AGM : Absorbent Glass Material
|
|
–
|
CMF : Closed Maintenance Free
|
|
| 2.
|
Battery capacity (20 Ah)
|
| 3.
|
Terminal location
|
–
|
L : battery positive ( + ) terminal on the left
|
|
–
|
R : battery positive ( + ) terminal on the right
|
|
| 4.
|
Battery type
|
–
|
BCI (Battery Council International) : Intruding terminal
|
|
–
|
DIN (Deutsche Industric Normen) : Recessed terminal
|
|
| 5.
|
Cold Cranking Ampere (CCA)
|
CCA : The amount of current that can be supplied for 30 seconds while
maintaining a voltage of
more than 7.2 V at -18°C (-0.4°F).
|
|
| 7.
|
Reserve Capacity (RC)
|
RC : The amount of time that can be supplied 25 A while maintaining the minimum
voltage of 10.5 V
at 26.7°C (80°F).
|
|
Battery Removal and Installation
|
Carefully inspect the battery case for cracks or leakage of electrolytes, and wear thick rubber
gloves to
prevent the electrolyte from contacting the skin when disconnecting the battery.
|
| 1.
|
Disconnect the battery negative ( - ) terminal (A) after loosening the nut.
|
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|
|
| 2.
|
Open the battery positive ( + ) terminal cover (A).
|
| 3.
|
Disconnect the battery positive ( + ) terminal (A) after loosening the nut.
|
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|
|
| 4.
|
Remove the battery clamp (A) after removing the bolt.
|
Tightening torque :
8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)
|
|
| 5.
|
Remove the battery (A).
|
| 1.
|
Remove the battery.
(Refer to Battery - "Removal and Installation")
|
| 2.
|
Remove the air cleaner assembly.
(Refer to Engine Mechanical System - "Air Cleaner")
|
| 3.
|
Remove the Engine Control Module (ECM).
(Refer to Engine Control/Fuel System - "Engine Control Module
(ECM)")
|
| 4.
|
Remove the wiring protector (A) after removing the bolt.
|
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
| 5.
|
Remove the fuel tube holder (A) from the battery tray.
|
| 6.
|
Remove the battery tray (A) after removing bolts.
|
Tightening torque :
8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)
|
|
| 1.
|
Install in reverse order of removal.
|
•
|
Install the battery and battery tray to the specified torque.
|
|
•
|
If the battery is dropped, it may cause internal damage. (Do
not reuse)
|
|
•
|
When installing the battery, fix the clamp on the tray
correctly.
|
|
•
|
When installing the battery ( - ) terminal, be sure to observe
the specified torque
before tightening. When tightening with excessive torque, the
circuit inside the PCB of the
battery sensor and the battery terminals may be damaged.
|
|
•
|
When replacing the battery, be sure to replace it with the same
specification(capacity,
manufacturer, etc.) as the battery installed originally. When
the different specification is
installed, it may be determined that the battery performance is
abnormal by the battery
sensor.
|
|
|
Battery Cleaning
| 1.
|
Remove the battery.
(Refer to Battery - "Removal and Installation")
|
| 2.
|
If the battery tray area is damaged due to an electrolyte leak, dissolve baking soda in warm
water to
clean the damaged area. Rub the damaged area with a stiff brush or the like, then wipe with a
cloth
moistened with an aqueous solution of baking soda.
|
| 3.
|
Wash the upper part of the battery with an aqueous solution of baking soda.
|
| 4.
|
Check the battery case and cover for the cracks, and replace the battery if any cracks are
found.
|
| 5.
|
Clean the battery post with a suitable tool.
|
| 6.
|
Clean the inside of the battery terminal clamp with a suitable tool and replace any damaged
cables or
damaged terminal clamps.
|
| 7.
|
Install the battery in the reverse order of removal.
|
Battery Sensor Specification
Item
|
Specification
|
Rated voltage (V)
|
12 - 14
|
Operating voltage (V)
|
6 - 18
|
Current consumption (mA)
|
Maximum 0.2 (on Low Power Mode)
|
Battery Sensor Components and Components Location
1. Battery
|
2. Battery Sensor 2-a. 7.8 - 9.8 N·m (0.8 -
1.0
kgf·m, 5.8 - 7.2 lb·ft) 2-b. 26.5 - 32.4 N·m (2.7 - 3.3 kgf·m, 19.5 - 23.9 lb·ft)
|
Battery Sensor Description and Operation
Battery sensor is mounted on the battery negative ( - ) terminal. It transmits battery voltage, current,
temperature information to Engine Control Module (ECM). ECM controls generating voltage by duty cycle based on
these
signals.
Battery Sensor On Vehicle Inspection
| 1.
|
Check the parasitic current.
(Refer to Charging System - "Battery")
|
If the parasitic current is more than 100 mA, a fault code may occur in the
battery sensor. If
the battery sensor fault code is displayed, measure the parasitic current first
before proceeding
with the battery sensor replacement procedure.
|
|
| 2.
|
If the parasitic current is normal, replace the battery sensor and perform the following
procedure.
| (1)
|
Turn the IG ON/OFF once and park the vehicle for at least 4 hours at room
temperature. In order
to measure the initial value of the State of Charge(SOC) of the battery, battery
needs stabilization
time.
|
| (2)
|
After 4 hours, START ON/OFF twice or more and check the State of Function (SOF)
of the battery
with the KDS.
|
|
Battery Sensor Removal and Installation
| 1.
|
Remove the battery.
(Refer to Charging System - "Battery")
|
| 2.
|
Disconnect the battery sensor connector (A).
|
| 3.
|
Remove the battery sensor (A) after removing the bolt.
|
Tightening torque :
26.5 - 32.4 N·m (2.7 - 3.3 kgf·m, 19.5 - 23.9 lb·ft)
|
|
| 1.
|
Install in reverse order of removal.
|
•
|
Install the battery sensor to the specified torque.
|
|
•
|
If the battery sensor is dropped, it may cause internal damage.
(Do not reuse)
|
|
•
|
When installing the battery ( - ) terminal, be sure to observe
the specified torque
before tightening. When tightening with excessive torque, the
circuit inside the PCB of the
battery sensor and the battery terminals may be damaged.
|
|
•
|
When replacing the battery, be sure to replace it with the same
specification(capacity,
manufacturer, etc.) as the battery installed originally. When
the different specification is
installed, it may be determined that the battery performance is
abnormal by the battery
sensor.
|
|
|