Contents:
Inside Mirror Assembly Removal and Installation
| 1.
|
Remove the multi sensor cover.
(Refer to Roof Trim - "Multi Sensor Cover")
|
| 2.
|
Disconnect the inside mirror connector (A).
|
| 3.
|
Remove the mirror (A) after removing the screw.
|
| 1.
|
Install in the reverse order of removal.
|
Outside Mirror Assembly Removal and Installation
| 1.
|
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
|
| 2.
|
Disconnect the outside mirror connector (A).
|
| 3.
|
Remove the outside mirror assembly (A) after removing the bolts.
|
Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
|
|
| 1.
|
Install in the reverse order of removal.
|
Outside Mirror Assembly Disassembly and Reassembly
Tool Name / Number
|
Illustration
|
Description
|
Outside rear view mirror glass remover tool 0K876 - L2100
|
|
Used when removing outside rear view mirror glass
|
Outside view mirror assembly fixing stand 0K876 - C5100
|
|
Used when fixing the outside rear view mirror assembly
|
|
•
|
When disassembling the outside rear view mirror, use of special tools can
improve workability and
safety against damage to parts.
|
|
•
|
The parts where can be worked in assembled state such as scalp or others,
proceed with the work
on vehicle.
|
|
•
|
The use of special tool is as below.
|
|
•
|
The indication below represents the location of a clip or fastener.
|
Outside View Mirror Assembly Fixing Stand (0K876 -
C5100)
| 1) |
Mount the special tool bolt (B) to the outside rear view mirror assembly (A)
and tighten the bolt
fixing nut (C) to fix it so that it does not move.
|
| 2) |
Turn the handle (B) to set the outside rear view mirror assembly (A) to
position where is easy to
work.
|
Outside Rear View Mirror Glass Remover Tool (0K876 -
L2100)
| 1) |
Remove the mirror (A) by applying slight force, after inserting the special
tools as shown below.
|
|
Mirror
| 1.
|
Remove the mirror (A).
|
| 2.
|
Disconnect the mirror heated wire connectors (A) and rear corner radar indicator connector (B).
|
Mirror Actuator
| 2.
|
Remove the mirror actuator (A) after removing the screws.
|
| 3.
|
Disconnect the mirror actuator connector (A).
|
Housing Cover
| 2.
|
Remove the cover (A) after removing the screws.
|
Scalp
| 1.
|
Remove the housing cover.
|
| 2.
|
Remove the scalp (A).
|
Lower Cover
| 2.
|
Remove the lower cover (A).
|
| 3.
|
Disconnect the wide angle side camera connector (A).
|
Side Repeater Lamp
| 1.
|
Remove the lower cover.
|
| 2.
|
Remove the lamp (A).
|
| 3.
|
Disconnect the lamp connector (A).
|
| 1.
|
Reassemble in the reverse order of disassembly.
|
Other information:
Kia K4 (CL4) 2025-2026 Service Manual: Intelligent Variable Transmission (IVT)
The Intelligent Variable Transmission (IVT) in your Kia K4 is an advanced gearbox designed to automatically adjust gear ratios in real-time, providing an optimal balance between engine efficiency, fuel economy, and driving performance based on your speed and accelerator pedal input.
Engage the brake pedal and the shift lock release button whenever you shift the gear lever.
Kia K4 (CL4) 2025-2026 Service Manual: Limitations of Forward Collision-Avoidance Assist
While the Forward Collision-Avoidance Assist (FCA) system is designed to enhance safety in your Kia K4, its operational effectiveness can be impacted by complex traffic dynamics and environmental surroundings. Understanding these boundaries is essential for the responsible operation of your Kia K4.
The operational range and responsiveness of the system may decrease depending on the behavior of vehicles ahead and the surrounding driving environment.