Kia K4: Brake System / Parking Brake System

Contents:

Components and Components Location

Components and Components Location

Brake System — Parking Brake System / Components and Components Location illustration

1. ESC (Electronic Stability Control) Control Unit
2. EPB Switch
3. Electronic Parking Brake (EPB) Actuator

Electronic Parking Brake (EPB) Description and Operation

Description
The Electric Parking Brake (EPB) is a parking brake system that operates the actuators of each caliper using an electrical signal via button operation, unlike a parking brake operated by a lever or pedal. The EPB has the function to engage the parking brake when the vehicle is stationary, to assist in braking in emergencies due to brake failure, and to engage the parking brake automatically when the engine off. EPB Main function
1. Static Apply It is a function of manually engaging the parking brake by pulling the EPB switch while the vehicle is stationary, the brake warning lamp is illuminated on the instrument panel.
2. Reduced Clamp Force on Flat (RCF) The EPB operates with different forces depending on the slope. If the driver operates the EPB switch for more than 3 seconds, it is operated with full force.
3. Static Release The park brake can be released by manually pressing the EPB switch. However, the conditions below must be met.
(1) IG ON
(2) Brake pedal pressed
The parking brake cannot be released when the ignition is switched off.
4. Auto Operation Release 1) DAR (Drive Away Release) The parking brake can be automatically released by pressing the accelerator pedal slowly if all of the following conditions are met:
(1) Engine is running
(2) Driver is wearing seat belt
(3) Driver's door, PE room hood and tailgate closed
(4) The shifting lever on the 'R' or 'D'
2) P/N to X (1) Engine is running (2) Press the brake pedal (3) Shifting gear to the driving stage (R/D) from the non-driving stage (P/N)
5. Electric Controlled Deceleration (ECD) When the driver operates the EPB switch while driving, the vehicle decelerates by transmitting a signal to the ESC. (used in emergency situations such as brake system failure). The system uses ESC hydraulic brakes, not EPB actuators.
6. Rear Wheel Unlocker (RWU)
– If the EPB switch is operated while driving in the event of an ESC failure, it decelerates the vehicle by operating the EPB actuator. (Adjusting rear wheels to prevent locking)
7. Key Off Apply (KOA)
– When the AUTO HOLD switch is on, the park brake is applied when the vehicle is stopped and the ignition is switched off. This function does not work when the EPB switch is pressed when the ignition is switched off.
8. Roll Away Reclamp (RAR)
– This is the function to re-engage the parking brake if the vehicle moves after parking. The vehicle's movement can be determined at wheel speed and monitored up to the time received by CAN communication.
9. High Temperature Reclamp (HTR)
– If the brake is overheated when the parking brake is engaged, it automatically re-engages the parking brake after a certain period of time to compensate for the loss of fastening force caused by temperature difference. Operating condition : more than 350°C (662°F)
10. External Apply / Release (EAR)
– This is a parking brake application function at the request of another system. (ESC command enables AVH -> EPB applying)
11. Pad Change Mode
– This function release the rear brake caliper piston to replacing brake pad using KDS.
Emergency Parking Brake Release (Manual) This is a method of operation for manually releasing the park brake emergency when the EPB is not applied. This is the last method used when it is impossible to release by KDS or electrical means due to direct damage to the actuator or EPB, or open power wires.
Warning    
The work must be done in a flat and safe place and when the parking brake is released, it must be done safely to prevent the vehicle from moving.
1. Remove the screw (A) of the rear caliper installed to the vehicle.

Brake System — Parking Brake System / Electronic Parking Brake (EPB) / Description and Operation / Description illustration

2. Using the tool used for screw removal, manually release the parking brake by turning the spindle (B) 0.5 to 1 time.
Auto Hold It is a function that remains stationary even when the vehicle is released from the brake pedal after pressing the brake pedal in shift lever D/N or sport mode. If the driver presses the accelerator pedal in D or sports mode, the parking brake status is automatically released and the vehicle can be started. Auto hold does not work under the following conditions :
– Engine hood open
– EPB operating
– Shift lever on 'P'
– Tail gate open
– When the driver's door is open
In the auto hold (green light), the following conditions occur and are switched to the parking brake (EPB actuation) for safety purposes: The "AUTO HOLD" indicator changes from green to white, and the red brake warning lamp turns on.
– Engine hood open
– EPB operating
– Shift lever on 'P'
– Tail gate open
– When the driver's door is open
1. Setting
(1) With the driver's door, engine hood, tail gate closed, press the AUTO HOLD switch. At this point, the white "AUTO HOLD" indicator is illuminated on the instrument panel.
(2) When the brake pedal is pressed while driving and the vehicle is stopped, the "AUTO HOLD" indicator changes from white to green as the automatic stop function is activated. At this point, the vehicle remains stationary even when the brake pedal is released.
(3) If the EPB is in operation, the automatic stop function will not work and the indicator will remain white.
2. Release To off the AUTO HOLD manually, push the AUTO HOLD switch while pressing the brake pedal, 'AUTO HOLD' light will be off.

Electronic Parking Brake (EPB) On Vehicle Inspection

On Vehicle Inspection
1. The brake system can quickly diagnosed for problems by using the KDS (Refer to "DTC guide").
(1) Trouble code diagnosis : Inspection and display trouble code (DTC) (Refer to DTC guide when fault code is found.)
(2) S/W Management : Controlling other features including system option setting and zero point adjustment.
Information    
Refer to the KDS screen for operating conditions and details

Electronic Parking Brake (EPB) Replacement

Replacement
[EPB Switch]
Note    
The EPB switch is supplied as an assembly with the crash pad side switch, so exchange as an assembly.
1. Exchange the crash pad side switch. (Refer to Body - "Crash Pad Side Switch")
[EPB Control Module (ESC Control Unit (ESC))]
1. Exchange the ESC Control Unit. (Refer to ESC (Electronic Stability Control) System - "ESC Control Unit")

Other information:

Kia K4 (CL4) 2025-2026 Service Manual: Intelligent Variable Transmission (IVT)

The Intelligent Variable Transmission (IVT) in your Kia K4 is an advanced gearbox designed to automatically adjust gear ratios in real-time, providing an optimal balance between engine efficiency, fuel economy, and driving performance based on your speed and accelerator pedal input. Engage the brake pedal and the shift lock release button whenever you shift the gear lever.

Kia K4 (CL4) 2025-2026 Service Manual: Fuses

Fuse types in the Kia K4 electrical system Figure 1. Blade type Figure 2. Cartridge type Figure 3.

Contents

Categories

Copyright © 2026 Kia K4 Manuals � 0.0193