Kia K4: Body (Interior / Exterior / Electrical) / Exterior Green House

Contents:

Components and Components Location

Component
Exterior Green House [4DR]

Body (Interior / Exterior / Electrical) — Exterior Green House / Components and Components Location / Component illustration

1. Washer Reservoir
1-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
2. Front Wiper Arm
2-a. 22.6 - 26.5 N·m (2.3 - 2.7 kgf·m, 16.6 - 19.5 lb·ft)
3. Cowl Top Cover Garnish
4. Cowl Top Cover


5. Wiper Motor
5-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
6. Windshield Glass
7. Rear Window Glass
8. Quarter Fixed Glass
8-a. 4.0 - 6.0 N·m (0.41 - 0.61 kgf·m, 3.0 - 4.4 lb·ft, 35.6 - 52.9 lb·in)

Exterior Green House [5DR]

Body (Interior / Exterior / Electrical) — Exterior Green House / Components and Components Location / Component illustration

1. Washer Reservoir
1-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
2. Front Wiper Arm
2-a. 22.6 - 26.5 N·m (2.3 - 2.7 kgf·m, 16.6 - 19.5 lb·ft)
3. Cowl Top Cover Garnish
4. Cowl Top Cover
5. Front Wiper Motor
5-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
6. Windshield Glass
7. Rear Wiper Arm
7-a. 8.8 - 12.7 N·m (0.9 - 1.3 kgf·m, 6.5 - 9.4 lb·ft)
8. Rear Wiper Motor
8-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
9. Rear Window Glass
10. Quarter Fixed Glass
10-a. 0.4 - 0.6 N·m (0.41 - 0.61 kgf·m, 3.0 - 4.4 lb·ft, 35.6 - 52.9 lb·in)


Cowl Top Cover Removal and Installation

Removal
Information    
The indication below represents the location of a clip or fastener.

Body (Interior / Exterior / Electrical) — Exterior Green House / Cowl Top Cover / Removal and Installation / Removal illustration

1. Remove the front wiper arm. (Refer to Exterior Green House - "Wiper Arm")
2. Remove the cowl top cover garnish (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Cowl Top Cover / Removal and Installation / Removal illustration

3. Separate the washer nozzle (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Cowl Top Cover / Removal and Installation / Removal illustration

4. Remove the cowl top cover (A) after removing the fasteners.

Body (Interior / Exterior / Electrical) — Exterior Green House / Cowl Top Cover / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.

Quarter Fixed Glass Removal and Installation - 4DR

Removal
Information    
The indication below represents the location of a clip or fastener.

Body (Interior / Exterior / Electrical) — Exterior Green House / Quarter Fixed Glass / Removal and Installation - 4DR / Removal illustration

1. Remove the rear pillar trim. (Refer to Interior Trim - "Rear Pillar Trim")
2. Remove the quarter fixed glass (A) after removing the nuts.
Tightening torque: 4 - 6N·m (0.41 - 0.61 kgf·m, 3.0 - 4.4 lb·ft, 35.6 - 52.9 lb·in)

Body (Interior / Exterior / Electrical) — Exterior Green House / Quarter Fixed Glass / Removal and Installation - 4DR / Removal illustration

Body (Interior / Exterior / Electrical) — Exterior Green House / Quarter Fixed Glass / Removal and Installation - 4DR / Removal illustration

Installation
1. Install in the reverse order of removal.

Quarter Fixed Glass Removal and Installation - 5DR

Removal
Information    
The indication below represents the location of a clip or fastener.

Body (Interior / Exterior / Electrical) — Exterior Green House / Quarter Fixed Glass / Removal and Installation - 5DR / Removal illustration

1. Remove the rear pillar trim. (Refer to Interior Trim - "Rear Pillar Trim")
2. Remove the C pillar garnish. (Refer to Body Side Molding - "C Pillar Garnish")
3. Remove the quarter fixed glass (A) after removing the nuts.
Tightening torque: 4 - 6 N·m (0.41 - 0.61 kgf·m, 3.0 - 4.4 lb·ft, 35.6 - 52.9 lb·in)

Body (Interior / Exterior / Electrical) — Exterior Green House / Quarter Fixed Glass / Removal and Installation - 5DR / Removal illustration

Body (Interior / Exterior / Electrical) — Exterior Green House / Quarter Fixed Glass / Removal and Installation - 5DR / Removal illustration

Installation
1. Install in the reverse order of removal.

Rear Window Glass Removal and Installation

Removal
1. Remove the rear package tray trim. (Refer to Luggage Trim - "Package Tray Trim")
2. Disconnect the rear window glass heated wire connectors (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Removal illustration

3. Insert the piano wire (A) in the corner side.

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Removal illustration

4. Cut the sealant of forward edge side (B) by pulling the piano wire (A) left and right.

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Removal illustration

Caution    
• Be careful not to burn hands as the excessive heat may be generated while using the wire.
• Be careful as the wire may break when working.
5. Cut the sealant in the sections (A-A), (B-B), and (C-C) by pulling the piano wire left and right.

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Removal illustration

Caution    
• Be careful not to burn hands as the excessive heat may be generated while using the wire.
• Be careful as the wire may break when working.
6. Remove the rear window glass (A) carefully using a glass holder (B).

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Removal illustration

Installation
1. Clean the edges of the body panel and the rear window glass with alcohol, etc.
2. Apply the body primer to the edge of the body panel (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Installation illustration

Note    
• Be careful not to touch the primed surface with your hands, as water leakage may occur after the rear window glass is installed.
• Do not apply the glass primer to the body.
• Do not smear the primer-covered surface to any foreign materials.
3. Apply the glass primer to the edge of rear window glass.

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Installation illustration

Note    
• Be careful not to touch the primed surface with your hands, as water leakage may occur after the rear window glass is installed.
• Do not smear the primer-covered surface to any foreign materials.
4. Apply the sealant (B) around the rear window glass (A) using the sealant gun.

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Installation illustration

5. Using the glass holder, adjust the rear window glass (A) to stopper hole (B) on the body and carefully tap the rear window glass to make the edges fully seated on the bonding surface of body.

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Installation illustration

6. Connect the rear window heated wire connector (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Rear Window Glass / Removal and Installation / Installation illustration

7. Perform a water leak test at least 3 to 4 hours later after installing the rear window glass.
Note    
Keep the water stream away from directly touching the newly installed adhesive surface and let the water fall on the side of the glass.
8. If a water leak occurs, apply sealant to the water leak area.
Note    
• Leave the car on a flat surface for at least 4 hours after installing the rear window glass. If driving the car is inevitable, drive at a low speed in least 8 hours.
• The driver should be careful to drive the vehicle aggressively or avoid uneven road driving for 2-3 days.
9. Install in the reverse order of removal.

Windshield Glass Removal

Removal
1. Remove the front pillar trim. (Refer to Interior Trim - "Front Pillar Trim")
2. Remove the inside mirror assembly. (Refer to Mirror - "Inside Mirror")
3. Remove the auto defogging sensor. (Refer to Heater and Air Conditioning Unit - "Auto Defogging Sensor")
4. Remove the front view camera unit. (Refer to Advanced Driver Assistance Systems (ADAS) - "Front Camera")
5. Remove the cowl top cover. (Refer to Exterior Green House - "Cowl Top Cover")
6. Insert the piano wire (A) in the corner side.

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Removal illustration

7. While pulling the piano wire (A) in the direction of the arrow, cut out the sealant on the front edge side (B).

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Removal illustration

8. Cut the sealant in sections (A-A) and (B-B) while pulling the piano wire left and right.

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Removal illustration

9. Cut the sealant in section (A-A) using a cutter knife.

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Removal illustration

Note    
Cut the sealant carefully as it may damage the crash pad when working the area (A-A). Be careful not to damage the body painting surface.
Information    
When using a cutter knife, use the blade of a knife with a 20 to 30 cm-long.
10. Remove the windshield glass (A) carefully by using a glass holder (B).

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Removal illustration

11. Remove the glass molding (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Removal illustration

Windshield Glass Installation

Removal
Note    
When replacing with the windshield glass of the front camera type, be sure to replace with the type equipped with the coupler. If the coupler is attached to the windshield glass type that is not equipped with the coupler, the front camera may not work properly.
1. Cut off leaving about 2 mm (0.079 in.) thick sealant at the bonding surface around the body panel by using a cutter knife. Marking the glass and body if a new windshield glass is used.
Note    
• Do not damage the body paintwork.
• If the body painting surface is damaged, apply the repair paint or anti-corrosion agent.
2. Clean the edges of the body panel and the windshield glass with alcohol, etc.
3. Apply the body primer to the edge of the body panel (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Installation / Removal illustration

Note    
• Do not touch the primed surface with your hands, as water leakage may occur after the windshield glass is installed.
• Do not apply the glass primer to the body.
• Do not smear the primer-covered surface to any foreign materials.
4. Attach the glass molding (A) to the windshield glass.

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Installation / Removal illustration

5. Apply the glass primer to the edge of windshield glass.

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Installation / Removal illustration

Note    
• Do not touch the primed surface with your hands, as water leakage may occur after the windshield glass is installed.
• Do not apply the glass primer to the body.
• Do not smear the primer-covered surface to any foreign materials.
• Apply the sealant within 5 minutes after applying the primer.
6. Apply the sealant (B) around the windshield glass (A) using the sealant.
Sealant Bead Width Height : 12 mm (0.47 in.) Width : 8 mm (0.31 in.)

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Installation / Removal illustration

7. Adjust the windshield glass (A) to stopper hole (B) of the body by using glass holder and carefully tap the windshield glass and press it against the body flange surface.

Body (Interior / Exterior / Electrical) — Exterior Green House / Windshield Glass / Installation / Removal illustration

8. Test for water leakage.
Note    
Keep the water stream away from directly touching the newly installed adhesive surface and let the water fall on the side of the glass.
9. If water leak occurs, apply sealant to the leak area.
Note    
• Leave the car on a flat surface for at least 4 hours after installing the windshield glass.
• If the vehicle needs to be used, drive slowly at least for 8 hours.
• The driver should be careful to drive the vehicle aggressively or avoid uneven road driving for 2 - 3 days.
10. Install in the reverse order of removal.
Note    
When installing the cowl top cover, install it after wiping the windshield glass which matches the cowl top cover.

Wiper Arm Removal and Installation

Removal
Front Wiper Arm
1. Remove the wiper arms (A) after removing the nuts.
Tightening torque: 22.6 - 26.5 N·m (2.3 - 2.7 kgf·m, 16.6 - 19.5 lb·ft)

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Arm / Removal and Installation / Removal illustration

Rear Wiper Arm [5DR Only]
1. Remove the wiper arm (A) after removing the nut.
Tightening torque: 8.8 - 12.7 N·m (0.9 - 1.3 kgf·m, 6.5 - 9.4 lb·ft)

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Arm / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• When installing, place the wiper arm to the specified position and then tighten the nut.
[Front Wiper]
– Place the wipers to the marking (A) position of cowl top cover.

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Arm / Removal and Installation / Installation illustration

– Place the wipers to the marking (A) position of windshield glass.

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Arm / Removal and Installation / Installation illustration

[Rear Wiper]
– Install the wiper arm to match the clear border (A) of the wiper assembly standard at the top of the tailgate glass.

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Arm / Removal and Installation / Installation illustration

Wiper Motor Removal and Installation

Removal
Front Wiper Motor
1. Remove the cowl top cover. (Refer to Exterior Green House - "Cowl Top Cover")
2. Remove the wiper motor and linkage assembly (A) after removing the bolts.
Tightening torque: 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Motor / Removal and Installation / Removal illustration

3. Disconnect the motor connector (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Motor / Removal and Installation / Removal illustration

Rear Wiper Motor [5DR Only]
1. Remove the rear wiper arm. (Refer to Exterior Green House - "Wiper Arm")
2. Remover the tailgate upper trim. (Refer to Tailgate - "Tailgate Trim")
3. Disconnect the motor connector (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Motor / Removal and Installation / Removal illustration

4. Remove the wiper motor (A) after removing the bolts.
Tightening torque: 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Motor / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of the removal.

Wiper Washer Motor On Vehicle Inspection

Inspection
Component Inspection
Washer Motor
1. The water pump may not operate according to the blockage of the filter for washer motor. Clean the filter if necessary.
Note    
Using wrong washer fluid may clog the washer pump and cause the malfunction of the pump motor.
2. Fill the washer fluid after installing the washer motor in the reservoir tank.
3. Connect terminal 1 to the battery ( - ) terminal and sequentially connect terminal 2 to the battery ( + ) terminal.
4. Check that the motor operates and that the washer fluid is properly spraying from the front and rear windshield.
5. Replace the washer motor if it is not normal.

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / On Vehicle Inspection / Inspection illustration

Terminal
Function
1
Ground
2
Front washer ( + )

Washer Fluid Level Sensor
1. Drain the washer fluid below the washer level sensor position.
2. Disconnect the sensor switch connector (2 pins) and check the current state between the terminals.

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / On Vehicle Inspection / Inspection illustration

Terminal
Function
1
Level sensor ( + )
2
Ground

Wiper Washer Motor Removal and Installation

Removal
Information    
The indication below represents the location of a clip or fastener.

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

Washer Motor
1. Remove the front bumper assembly. (Refer to Front & Rear Bumper - "Front Bumper Assembly")
2. Disconnect the motor connector (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

3. Remove the motor (A) after disconnecting the washer nozzle (B).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

Note    
Washer fluid is drained when removing washer motor.
Washer Level Sensor
1. Remove the front bumper assembly. (Refer to Front & Rear Bumper - "Front Bumper Assembly")
2. Disconnect the sensor connector (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

3. Remove the sensor (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

Washer Reservoir
1. Remove the head lamp. (Refer to Light & Vision System - "Head Lamp")
2. Remove the wheel guard. [Passenger's side] (Refer to Body Side Molding - "Wheel Guard")
3. Disconnect the washer motor connector (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

4. Disconnect the washer level sensor connector (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

5. Separate the washer nozzle (A).

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

6. Remove the washer reservoir (A) after removing the bolts and screw.
Tightening torque : 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)

Body (Interior / Exterior / Electrical) — Exterior Green House / Wiper Washer Motor / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.

Other information:

Kia K4 (CL4) 2025-2026 Service Manual: Airbag Module Disposal Procedure

Airbag Module Disposal Procedure When scrapping a vehicle equipped with an airbag system such as an airbag or seat Belt Pretensioner (BPT), the airbag must be deployed first. When deploying the airbag, it must be deployed by a skilled technician, and the used airbag cannot be reused, so it must not be installed in another vehicle.

Kia K4 (CL4) 2025-2026 Service Manual: Manual Speed Limit Assist (MSLA)

Speed Limit indicator Set speed value The Manual Speed Limit Assist (MSLA) feature in your Kia K4 allows you to establish a maximum speed limit to prevent the vehicle from inadvertently exceeding your desired pace.

Copyright © 2026 Kia K4 Manuals ⏱ 0.0134