Kia K4: Suspension System / Front Suspension System

Contents:

Front Stabilizer Bar Components and Components Location

Component and Component Location

Suspension System — Front Suspension System / Front Stabilizer Bar / Components and Components Location / Component and Component Location illustration

1. Front Stabilizer Bar Link
1-a. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
1-b. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
2. Front Stabilizer Bar
3. Front Stabilizer Bar Bushing
4. Front Stabilizer Bar Bracket
4-a. 44.1 - 53.9 N·m (4.5 - 5.5 kgf·m, 32.5 - 39.8 lb·ft)

Front Stabilizer Bar Removal and Installation

Removal
[Front Stabilizer Bar Link]
1. Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
2. Separate the stabilizer bar link (A) after removing the nut.
Tightening torque : 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

Note    
• When removing and installing the stabilizer bar link nut, fix the outer hexa stud (A) of the link.

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

• Be careful not to damage the boot of the link.
• Use only a hand tool when removing or installing the stabilizer bar link nut.
3. Remove the stabilizer bar link (A) after removing the nut.
Tightening torque : 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

Note    
• When removing and installing the stabilizer bar link nut, fix the outer hexa stud (A) of the link.

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

• Be careful not to damage the boot of the link.
• Use only a hand tool when removing or installing the stabilizer bar link nut.
[Front Stabilizer Bar]
1. Remove the front subframe. (Refer to Front Suspension System - "Front Subframe")
2. Remove the front stabilizer bar (A) after removing the bolts.
Tightening torque : 44.1 - 53.9 N·m (4.5 - 5.5 kgf·m, 32.5 - 39.8 lb·ft)

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
Install to the specified torque.
2. Check the alignment. (Refer to Alignment - "Repair Procedures")

Front Stabilizer Bar Inspection

Inspection
1. Check the stabilizer bar bushing for damage.
2. Check the stabilizer bar link ball joint for damage.

Front Stabilizer Bar Disassembly and Reassembly

Disassembly
1. Remove the stabilizer bar bushing bracket (A) using a flat-head screwdriver or suitable tool.

Suspension System — Front Suspension System / Front Stabilizer Bar / Disassembly and Reassembly / Disassembly illustration

Note    
Take care not to deform when removing and renew if deformed.
2. Remove the stabilizer bar bushing (A) using a flat-head screwdriver or suitable tool.

Suspension System — Front Suspension System / Front Stabilizer Bar / Disassembly and Reassembly / Disassembly illustration

Note    
Do not reuse the stabilizer bar bushing (A).
Reassembly
1. Reassemble in the reverse order of disassembly.

Front Strut Assembly Components and Components Location

Component and Component Location

Suspension System — Front Suspension System / Front Strut Assembly / Components and Components Location / Component and Component Location illustration

1. Strut Ring
2. Insulator Cap
3. Strut Insulator
3-a. 53.9 - 73.5 N·m (5.5 - 7.5 kgf·m, 39.8 - 54.2 lb·ft)
4. Strut Bearing
5. Bumper Rubber
6. Coil Spring
7. Dust Cover
8. Spring Lower Pad
9. Strut Assembly
9-a. 98.1 - 107.9 N·m (10.0 - 11.0 kgf·m, 72.3 - 79.6 lb·ft)
9-b. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
9-c. 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Front Strut Assembly Removal and Installation

Removal
1. Remove the front strut upper nuts (A).
Tightening torque : 53.9 - 73.5 N·m (5.5 - 7.5 kgf·m, 39.8 - 54.2 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

2. Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
3. Separate the front brake hose bracket (A) after removing the bolt.
Tightening torque : 8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 9.4 - 12.3 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

4. Separate the stabilizer bar link (A) after removing the nut.
Tightening torque : 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

Note    
• When removing and installing the stabilizer bar link nut, fix the outer hexa stud (A) of the link.

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

• Be careful not to damage the boot of the link.
• Use only a hand tool when removing or installing the stabilizer bar link nut.
5. Remove the front strut assembly (A) after removing the bolts and nuts.
Tightening torque : 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

Installation
1. Install in the reverse order of removal.
Note    
• Pre-tighten the front strut upper nuts and put the vehicle down on the ground and tighten the front strut upper nuts to tightening torque.
• Install to the specified torque.

Front Strut Assembly Disassembly

Special Service Tool
Tool Name / Number
Illustration
Description
Shock absorber lock nut remover
09546 - 3X100

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly / Special Service Tool illustration

Used for removal or installing of front strut assembly and rear shock absorber lock nut

Disassembly
1. Remove the front strut assembly. (Refer to Front Suspension System - "Front Strut Assembly")
2. Install the front strut assembly (A) to the spring compressor.

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

3. Remove the insulator cap (A).

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

4. Compress the coil spring (A) slightly until it is tensioned using the spring compressor.

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

Information    
Protect the coil spring when compressing using rubber such as plastic hose, etc to prevent damage.

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

5. Remove the nut using the SST (09546 - 3X100).
Tightening torque : 98.1 - 107.9 N·m (10.0 - 11.0 kgf·m, 72.3 - 79.6 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

6. Disassemble insulator (A), strut bearing (B), bumper stopper (C), dust cover (D), coil spring (E), spring lower pad (F) from the strut (G).

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

Front Strut Assembly Inspection

Inspection
1. Check the strut insulator bearing for wear and damage.
2. Check the rubber parts for damage and deterioration.
3. Compress and extend the piston rod (A) and check that there is no abnormal resistance or unusual sound during operation.

Suspension System — Front Suspension System / Front Strut Assembly / Inspection illustration

Disposal
1. Fully extend the strut rod.
2. Drill the (A) of the cylinder to deflate gas.

Suspension System — Front Suspension System / Front Strut Assembly / Inspection / Disposal illustration

Information    
The gas coming out is harmless, but be careful of debris that may fly when drilling.

Front Strut Assembly Reassembly

Special Service Tool
Tool Name / Number
Illustration
Description
Shock absorber lock nut remover.
09546 - 3X100

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly / Special Service Tool illustration

Used for removal or installing of rear shock absorber lock nut.

Reassembly
1. Assemble the insulator (A), strut bearing (B), bumper stopper (C), dust cover (D), coil spring (E), and spring lower pad (F) on the strut (G).

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

Note    
• Align the protrusions of the strut bearing upper housing and the lower housing when reassembling.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

• Align the protrusion of the insulator (A) and groove of the bearing when assembling.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

• When installing the insulator assembly and strut bearing to the front strut assembly, align the front knuckle mounting part (A) and protrusions (B).

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

• When installing the coil spring, make sure that the gap (A) between the spring top start and 180° past point (B) and the spring upper pad is within the allowable value.
Maximum allowable gap (A) : 3 mm (0.118 in.)

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

2. Install the front strut assembly (A) to the spring compressor.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

3. Compress the coil spring (A) slightly until it is tensioned using the spring compressor.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

Information    
Protect the coil spring when compressing using rubber such as plastic hose, etc to prevent the damage.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

4. Install the self locking nut using SST (09546 - 3X100).
Tightening Torque : 98.1 - 107.9 N·m (10.0 - 11.0 kgf·m, 72.3 - 79.6 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

Note    
Do not reuse the self locking nut.
5. Install the insulator cap (A).

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

6. Install the front strut assembly. (Refer to Front Suspension System - "Front Strut Assembly")

Front Subframe Components and Components Location

Component and Component Location

Suspension System — Front Suspension System / Front Subframe / Components and Components Location / Component and Component Location illustration

1. Front Subframe
1-a. 176.5 - 196.1 N·m (18.0 - 20.0 kgf·m, 130.2 - 144.7 lb·ft)
1-b. 176.5 - 196.1 N·m (18.0 - 20.0 kgf·m, 130.2 - 144.7 lb·ft)
2. Front Subframe Dynamic Damper
2-a. 44.1 - 53.9 N·m (4.5 - 5.5 kgf·m, 32.5 - 39.8 lb·ft)


Front Subframe Removal and Installation

Video Guide
Note    
• This video was created using 3D graphics to help understand the vehicle maintenance manual.
• There may be some differences from actual vehicles.
• The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
• Check the KDS Guide for detailed information on how to use the KDS.
• Check the manual for detailed maintenance procedures.
• Unauthorized reproduction, distribution, or sharing of this video is prohibited.
Front Subframe Removal (Click to play)Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Video Guide illustration

Video: Front Subframe Removal

Special Service Tool
Tool Name / Number
Illustration
Description
Ball joint puller
09568 - 1S100

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Special Service Tool illustration

Used for removal of tie rod end and lower arm ball joint

Removal
1. Align the steering wheel straight.
2. Disconnect the negative ( - ) battery terminal.
3. Fix the steering wheel (A) by using a suitable tool.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Note    
If the neutral position of the clock spring is changed by rotating the steering wheel while the steering column universal joint is removed, disconnection of the internal cable of the clock spring may be folded after installation.
4. Separate the universal joint assembly (A) from the steering gear box after removing the bolt.
Tightening torque : 49.0 - 58.8 N·m (5.0 - 6.0 kgf·m, 36.2 - 43.4 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Note    
Do not reuse the universal joint assembly bolt.
5. Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
6. Remove the stabilizer bar link (A) from the front strut assembly after removing the nut.
Tightening torque : 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Note    
• When removing and installing the stabilizer bar link nut, fix the outer hexa stud (A) of the link.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

• Be careful not to damage the boot of the link.
• Use only a hand tool when removing or installing the stabilizer bar link nut.
7. Separate the tie rod end ball joint from the front knuckle.
(1) Remove the split pin (A).
(2) Remove the lock nut (B).
Tightening torque : 34.3 - 44.1 N·m (3.5 - 4.5 kgf·m, 25.3 - 32.5 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Note    
• Do not reuse the split pin.
• Do not reuse the lock nut.
• Be careful not to damage the ball joint boot.
• Use a hand tool when removing or installing the lock nut.
(3) Separate the tie rod end ball joint (A) using SST (09568 - 1S100).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

8. Separate the lower arm ball joint from the front knuckle.
(1) Remove the lock nut (A).
Tightening torque : 68.6 - 80.4 N·m (7.0 - 8.2 kgf·m, 50.6 - 59.3 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Note    
• Do not reuse the lock nut.
• Be careful not to damage the ball joint boot.
• Use a hand tool when removing or installing the lock nut.
(2) Separate the lower arm ball joint (A) using SST (09568 - 1S100).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

9. Remove the engine room under cover. G 1.6 T-GDI GAMMA II (Refer to Engine Mechanical System- "Engine Room Under Cover") G 2.0 MPI NU(ATKINSON) (Refer to Engine Mechanical System- "Engine Room Under Cover")
10. Separate the muffler hanger rubber (A) from the front subframe.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

11. Remove the roll rod support bolt (A).
Tightening torque : 107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Note    
Do not reuse the bolt.
12. Remove the wheel guard fasteners (A).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

13. Support the front subframe with a suitable jack (A).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Warning    
Be careful not to lift the vehicle too much. A change in the center of gravity may cause the vehicle to fall.
Caution    
If a small jack such as a mission jack is used when removing and installing the subframe, the subframe may lean to one side and there may be a risk of injury, so use an appropriately sized jack to work safely.
Information    
When installing or removing the front subframe bolts and nuts, adjust the table lift position.
14. Remove the front subframe bolts and nuts (A).
Tightening torque : 176.5 - 196.1 N·m (18.0 - 20.0 kgf·m, 130.2 - 144.7 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

15. Remove the front subframe by lowering the jack (A).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Note    
Be careful not to interfere with the surrounding parts when removing the front subframe.
16. Remove the steering gear box heat protector (A) after removing the bolts.
Tightening torque : 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft, 60.8 - 95.5 lb·in)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

17. Remove the steering gear box (A) after removing the bolts.
Tightening torque : 107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

18. Remove the front stabilizer bar (A) after removing the bolts.
Tightening torque : 44.1 - 53.9 N·m (4.5 - 5.5 kgf·m, 32.5 - 39.8 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

19. Remove the roll rod (A) after removing the bolts.
Tightening torque : 49.0 - 63.7 N·m (5.0 - 6.5 kgf·m, 36.2 - 47.0 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

20. Remove the dynamic damper (A) after removing the nuts.
Tightening torque : 44.1 - 53.9 N·m (4.5 - 5.5 kgf·m, 32.5 - 39.8 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

21. Remove the front lower arm (A) after removing the bolts and nuts (B, C).
Tightening torque : (B) : 63.7 - 73.5 N·m (6.5 - 7.5 kgf·m, 47.0 - 54.2 lb·ft) + 175 - 185° (C) : 63.7 - 73.5 N·m (6.5 - 7.5 kgf·m, 47.0 - 54.2 lb·ft) + 265 - 275°

Suspension System — Front Suspension System / Front Subframe / Removal and Installation / Removal illustration

Note    
Do not reuse the front lower arm bolt and nut.
Installation
1. Install in the reverse order of removal.
Note    
Install to the specified torque.
2. Check the alignment. (Refer to Alignment - "Repair Procedures")

Front Lower Arm Components and Components Location

Component and Component Location

Suspension System — Front Suspension System / Front Lower Arm / Components and Components Location / Component and Component Location illustration

1. Snap Ring
2. Lower Arm Ball Joint
3. Lower Arm 'G' Bushing
4. Lower Arm
4-a. 63.7 - 73.5 N·m (6.5 - 7.5 kgf·m, 47.0 - 54.2 lb·ft) + 175 - 185°
4-b. 63.7 - 73.5 N·m (6.5 - 7.5 kgf·m, 47.0 - 54.2 lb·ft) + 265 - 275°

Front Lower Arm Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Ball joint puller
09568 - 1S100

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Special Service Tool illustration

Used for removal of tie rod end and lower arm ball joint

Removal
1. Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
2. Remove the engine room under cover. G 1.6 T-GDI GAMMA II (Refer to Engine Mechanical System- "Engine Room Under Cover") G 2.0 MPI NU(ATKINSON) (Refer to Engine Mechanical System- "Engine Room Under Cover")
3. Separate the lower arm ball joint from the front knuckle.
(1) Remove the lock nut (A).
Tightening torque : 68.6 - 80.4 N·m (7.0 - 8.2 kgf·m, 50.6 - 59.3 lb·ft)

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Note    
• Do not reuse the lock nut.
• Be careful not to damage the ball joint boot.
• Use a hand tool when removing or installing the lock nut.
(2) Separate the lower arm ball joint (A) using SST (09568 - 1S100).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

4. Remove the front lower arm (A) after removing the bolts and nuts (B, C).
Tightening torque : (B) : 63.7 - 73.5 N·m (6.5 - 7.5 kgf·m, 47.0 - 54.2 lb·ft) + 175 - 185° (C) : 63.7 - 73.5 N·m (6.5 - 7.5 kgf·m, 47.0 - 54.2 lb·ft) + 265 - 275°

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Note    
Do not reuse the front lower arm bolt and nut.
Installation
1. Install in the reverse order of removal.
Note    
Install to the specified torque.

Front Lower Arm Replacement - Lower Arm Ball Joint

Replacement
1. Remove the snap ring (A).

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm Ball Joint / Replacement illustration

Note    
Do not reuse the snap ring (A).
2. Remove the front lower arm ball joint (A) using a press.

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm Ball Joint / Replacement illustration

Information    
Place the suitable adapter (B) under the front lower arm ball joint.
Caution    
• Make sure that the lower arm ball joint is secured before pressing.
• Wear protective glasses while using a press.
• Keep hands and fingers away from all clamping and moving parts.
3. Install the new front lower arm ball joint (A) using a press.

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm Ball Joint / Replacement illustration

Information    
Place the suitable adapter (B) under the front lower arm ball joint.
Caution    
• Make sure that the lower arm ball joint is secured before pressing.
• Wear protective glasses while using a press.
• Keep hands and fingers away from all clamping and moving parts.
4. Install a new snap ring (A).

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm Ball Joint / Replacement illustration

Note    
Do not reuse the snap ring (A).

Front Lower Arm Replacement - Lower Arm 'G' Bushing

Special Service Tool
Tool Name / Number
Illustration
Description
Lower arm 'G' bushing replacement tool
09545 - AL100

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing / Special Service Tool illustration

Used for replacement of the lower arm 'G' bushing

Replacement - Lower Arm 'G' Bushing
Information    
Replace the lower arm 'G' bushing if it only has a crack, noise from bushing without cracks can be improved by applying silicone oil.
1. Replace the lower arm 'G' bushing by using the SST (09545 - AL100).

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

Information    
Refer to the enclosed manual for detailed usage instructions.
Caution    
• Wear personal protective equipment during press operation.
• When the press is in operation, ensure that no part of the body comes into contact within the operating range.
• Due to the risk of injury from falling tools and parts, before operating the press, ensure that all tools and components are securely positioned in their proper places.
Note    
• Lubricate the bushings and mounting surface with grease during the operation.
• Measure the void spacing (A), (B) to ensure that the bushing can be properly installed in the correct direction.
(A) : Ball joint side (B) : Opposite side

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

Information    
• Refer to the enclosed manual for void spacing specifications for each vehicle model.
• There may be no difference in void spacing for used bushing due to wear.
• Be careful not to install the bushing at the incorrect angle.
Installaion angle (A) : Angle formed counterclockwise from 'A' bushing (B) and 'G' bushing (C) reference

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

Information    
Refer to the enclosed manual for installation angle specifications for each vehicle model.
• Clean the bushing mounting surface (A) from any foreign substances using a clean cloth or similar material when installing.

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

• Ensure that the marking angle (A) of the bushing and the lower arm does not deviate from the reference value.
Reference Value : ± 3°

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

• If excessive pressure is applied after installation is complete, it may result in damage to the components and tools.

Front Lower Arm Inspection

Inspection
1. Check the bushing for wear or aging.
2. Check the lateral arm for bent or damaged.
3. Check the ball joint for wear and aging.
4. Check all bolts and nuts.

Other information:

Kia K4 (CL4) 2025-2026 Service Manual: Engine Oil and Filter Replacement

Video Guide     • This video was created using 3D graphics to help understand the vehicle maintenance manual.

Kia K4 (CL4) 2025-2026 Service Manual: Lane Following Assist (LFA)

The Lane Following Assist (LFA) system is a sophisticated driver-assistance feature designed to enhance your comfort and safety. By utilizing advanced sensor technology, the Kia K4 can actively detect lane markings or the position of a vehicle traveling directly ahead. The system then provides subtle steering support to help keep your Kia K4 centered within its lane, significantly reducing driver fatigue during long journeys or highway driving.

Copyright © 2026 Kia K4 Manuals ⏱ 0.0189